• Support for SATA Hot Plug 3.5" Midline (MDL) Solid State Drives
• Support for SAS Hot Plug 3.5" Enterprise (ENT) Hard Drives

• Processors:
  • Supports up to two Intel® Quad-Core 5400 or Dual-Core 5200 sequence processors
    • Quad-Core Intel® Xeon® processors 5400 sequence with 12 MB Level 2 cache
    • Dual-Core Intel® Xeon® processors 5200 sequence with 6 MB Level 2 cache
  • Intel® 5400 Chipset
• Memory:
  • Supports up to 64 GB of PC2-5300 (DDR2-667) and up to 32 GB of PC2-6400 (DDR2-800) fully buffered DIMMs (DDR2-667) with Advanced ECC
• Internal Drive Support:
  • Support for up to four 3.5" Non-Hot plug serial ATA (SATA) hard drives or;
  • Support for up to four 3.5" Hot plug Serial Attached SCSI (SAS) or SATA hard drives.
  • NOTE: Installation of the Hot Plug Backplane 1U 2S Kit (445985-B21) is required if ordering third or fourth Hard Drives for Hot Plug models only.
  • Internal storage capacity of up to 1.0TB (4 x 1TB Hot Plug 3.5" SATA), 3.0TB (4 x 750 Non-Hot Plug SATA) or 4.0TB (4 x 1TB Hot Plug 3.5" SAS)
• Network Controller:
  • Two embedded NC105i PCIe Gigabit Server Adapters
• Storage Controllers:
  • Non-Hot Plug SATA Models: HP Embedded SATA RAID Controller
    NOTE: Transfer rate: 1.5 Gb/s SATA
  • Hot Plug SAS/SATA Models: HP SC40Ge 4-Port Internal SAS HBA with RAID 0, 1
    NOTE: When using the SC40Ge with SATA Hard Drives, 1.5G SATA Hard Drives are required.
    NOTE: Transfer rate: 1.5 Gb/s SATA, 3Gb/s SAS
• Expansion Slots:
  • Non-Hot Plug Models: Two available PCI Express 2.0 slots:
    • Slot 1: full-length/full-height PCI-Express 2.0 x16
    • Slot 2: low-profile/half-height PCI-Express 2.0 x16
  • Hot Plug Models: One available PCI-Express slot:
  • Slot 1: full-length/full-height PCI-Express 2.0 x16
  • Slot 2: low-profile/half-height PCI-X slot populated by the SAS/SATA storage controller
• Infrastructure Management:
  • HP Lights Out 100i Advanced Remote Management with new licensed key activated upgrades for Virtual KVM and virtual media support. LO100i management support for the DL160 G5 includes:
  • IPMI 2.0 & SMASH CLP support
  • ROM Setup Utility
  • Improvements to virtual media with the addition of USB 2.0 drives and protocol support for much faster transfer speeds and DVD-ROM support plus simplified virtual media (floppy and CD with no FTTP server requirements)
  • Enhanced browser interface and embedded KVM over IP provides OS-independent remote graphical console
• USB Ports:
  • Five USB ports (two front, one internal, two rear)
• Optical Drive:
• Support for one (optional): DVD-ROM, DVD/CD RW
• Power Supply:
• 650W Power Supply (Non-Hot Plug, Autoswitching)
• Optional high-efficiency model
  • NOTE: Optional high-efficiency model requires the purchase of HP Power Supply Backplane (453652-B21)
• Additional Features:
• Support for:
  • NVIDIA Quadro FX3700 512MB PCIe x 16 graphics card
  • NVIDIA Quadro FX1700 512MB PCIe x 16 graphics card
• Form Factor:
  • Rack (1U)
  • Fixed mounting rails included with all models
• Deployment/Serviceability:
  • Tool-less access to all system components for easy in rack serviceability
  • Customer Self Repair (CSR): HP products are designed with many CSR parts to minimize repair time and allow for greater flexibility in performing defective parts replacement
• Warranty:
• This product is covered by a global limited warranty and supported by HP Services and a worldwide network of HP Authorized Channel Partners. Hardware diagnostic support and repair is available for one year from date of purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to warranty services are available through HP Care Pack services or customized service agreements. Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.
  NOTE: Server Warranty includes 1 year Parts, 1 year Labor, 1-year on-site support with next business day response. Warranty repairs may be accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity. Customers may choose to have HP replace Optional CSR parts at no charge. Additional information regarding worldwide limited warranty and technical support is available at: https://h18004.www1.hp.com/products/servers/platforms/warranty/index.html.

3.3 volts

1

32MB shared supporting 1600x1200x16M resolution

Lights-Out 100i

HP Lights-Out 100i Remote Management delivers affordable, entry level remote management capabilities for HP ProLiant 100 Series servers with embedded LO100i. It allows customers or their service providers to remotely manage ProLiant 100 Series servers remotely over a LAN or the Internet and consists of the following:

• LO100i Standard is embedded remote management and provides basic remote control via telnet, browser, and IPMI 2.0 and SMASH
• LO100i Advanced Pack License are upgrades for essential, secure, remote control, serial console, virtual media, and Virtual KVM (graphical hardware-based, remote console)

NOTE: Flexible and volume quantity (AKA) license kits are available for the Lights-Out 100i Lights-Out 100 Advanced Pack licenses as well as Electronic License To Use (E-LTU). AKA Tracking licenses require a 100 unit minimum forecast at initial contract signing. For these additional part numbers, please refer to each software products. QuickSpecs at this link for more information: www.hp.com/go/lo100.

HP Lights-Out 100i Standard provides the following OS-independent remote control capabilities:

• Virtual power
• System event log access
• System health
• Remote serial console (serial redirection)
• Browser, Telnet access
• SMASH-CLP compliant
• IPMI 2.0 compliant

HP Lights-Out 100i Advanced Pack provides license key activated upgrades to the following:

• Virtual KVM (KVM over IP functionality embedded on the system board)

One 6' Highline (IEC-IEC) power cord ships standard
NOTE: HP ProLiant DL servers no longer ship standard with NEMA power cords (163719-002) that allow connection to 110V wall outlets in a home or office. ProLiant DL servers are primarily connected to PDU's in data center racks so they now ship standard with only a PDU power cord (416151-B21). If a user wishes to power a ProLiant DL server using a 110V receptacle (NEMA-15), the NEMA power cord (227099-001) must be ordered separately.

If customers require a local power cord, they can check the power cord matrix for the appropriate cord. Please see the following power cord matrix: https://www.hp.com/go/powercordmatrix.

Installation into Telco 2 post, and 4 post, or threaded holes racks requires a 3rd party option kit. For additional information, please visit: www.racksolutions.com.

The HP eConfigure Enterprise Configurator now provides factory default racking for our HP hardware portfolio. This approach is aligned with our strategic direction to meet the needs and expectations of our valued customers. If you require "custom" rack configuration, please contact HP's Customer Business Center or an Authorized Partner for assistance.

HP Care Pack Services provide total care and support expertise with committed response designed to meet your IT and business needs.

HP Care Pack Services provide total care and support expertise with committed response designed to meet your IT and business needs.

HP Care Pack services include coverage for the HP branded hardware options qualified for the server that are purchased at the same time or afterward and internal to the enclosure. It also includes the 22" and smaller external monitors and tower UPS options up to 3kVA. These items will be covered at the same service level and for the same coverage period as the server. Coverage of UPS Battery is not included and standard warranty terms & conditions apply. For servers or storage systems installed within a rack, service also covers all HP qualified rack options installed within the same rack.

To fully capitalize on your HP ProLiant servers' capabilities requires a service partner who thoroughly understands your server technology and systems environment. HP Services, an industry leader in provision of multi vender support solutions provides a range of support services designed to meet the varying needs of business. Whether an SMB or large global corporation HP has a ProLiant server support offer to help you speedily deploy and maximize system uptime.

Recommended Service – Simplify ProLiant solution implementation, maintenance and management.

• Support Service – 3 Year, 9x5 Next Business Day coverage, excluding HP holidays only
• Deployment Service – Hardware Installation only

Enhanced Service – Optimize service level to increase IT performance and availability

• Support Service – 3 Year 13x5 Same Business Day, 4-Hour response coverage
• Deployment Service – Installation and Start-up only

Installation & Start-Up of a ProLiant server and Microsoft or Linux O/S per the Customer Description and/or Data Sheet. To be delivered on a scheduled basis 8am-5pm, M-F, excl. HP holidays.

For a complete listing of service offerings and information visit:
https://www.hp.com/services/proliantservices
https://www.hp.com/go/proliant/carepack

HP DL160 G5 X5472 Non-Hot Plug SATA, 2GB, (1P)
445198-001

HP DL160 G5 E5430 Non-Hot Plug SATA, 1GB, (1P)
445197-001

HP DL160 G5 E5405 Non-Hot Plug SATA, 1GB, (1P)
445196-001

HP DL160 G5 X5472 Hot Plug SAS/SATA, 2GB, (1P)
445204-001

HP DL160 G5 E5430 Hot Plug SAS/SATA, 1GB, (1P)
445203-001

HP DL160 G5 E5405 Hot Plug SAS/SATA 1GB, (1P)
445202-001

S-BUY DL160G5 E5405 NHP
481179-001

S-BUY DL160G5 E5430 2P
481180-001

S-BUY DL160G5
E5430
AM852A

Two available PCI-Express 2 slots:

Slot 1: full-length/full-height
Slot 2: low-profile/half-height

Two available PCI-Express 2 slots:

Slot 1: full-length/full-height
Slot 2: low-profile/half-height

Quad-Core Intel® Xeon® processor X5460 (3.16 GHz, 120W, 1333MHz FSB), FIO

HP 250GB 3G SATA 7.2K NHP 3.5" MDL HDD

HP Smart Array E200/128 BBWC Controller

HP StorageWorks D2D130 Backup System with LTO-3 Ultrium 920 SAS Tape Drive
NOTE: 3TB of Disk Storage.

Following are memory options available from HP:

Drive Support

DVD-ROM

Up to 1

A

Integrated IDE (ATAPI) (optional)

Up to 1

A

Integrated IDE (ATAPI) (optional)

Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.
NOTE: Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.

Up to 2 per SA-6402
Up to 4 per SA-6404

External

Smart Array 6402/128 Controller
Smart Array 6404/256 Controller
Smart Array 642 Controller

 412911-B21

N/A

HP SC44Ge Host Bus Adapter

 416096-B21

NOTE: Please visit: https://www.hp.com/go/connect for details about minimum SAS controller firmware version and SAS cabling requirements.

HP StorageWorks D2D Backup Systems
D2D120
D2D130
D2D2503i
D2D2504i
D2D4004i

One 6' Highline (IEC-IEC) power cord ships standard
NOTE: HP ProLiant DL servers no longer ship standard with NEMA power cords (163719-002) that allow connection to 110V wall outlets in a home or office. ProLiant DL servers are primarily connected to PDU's in data center racks so they now ship standard with only a PDU power cord (416151-B21). If a user wishes to power a ProLiant DL server using a 110V receptacle (NEMA-15), the NEMA power cord (227099-001) must be ordered separately.

If customers require a local power cord, they can check the power cord matrix for the appropriate cord. Please see the following power cord matrix: https://www.hp.com/go/powercordmatrix.

Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling programs in many geographic areas. For trade-in information, please go to: https://www.hp.com/go/green. To recycle your product, please go to: https://www.hp.com/go/green or contact your nearest HP sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.

The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each product type for use by treatment facilities. This information (product disassembly instructions) is posted on the Hewlett Packard web site at: https://www.hp.com/go/green. These instructions may be used by recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP equipment.