• Support for HP 900GB 6G SAS 10K rpm SFF (2.5-inch) Enterprise 3yr Warranty Hard Drive

This document covers the HP ProLiant BL620c G7 server blade only. For more information on the HP BladeSystem c-Class Enclosure and HP BladeSystem c-Class Interconnects, please see the following:
HP BladeSystem c3000 Enclosure QuickSpecs:
https://h18000.www1.hp.com/products/quickspecs/12790_na/12790_na.html
HP BladeSystem c7000 Enclosure QuickSpecs:
https://h18000.www1.hp.com/products/quickspecs/12810_na/12810_na.html
HP BladeSystem c-Class Interconnect and Mezzanine Components QuickSpecs: https://h18004.www1.hp.com/products/blades/components/c-class-interconnects.html
https://h18004.www1.hp.com/products/blades/components/c-class-adapters.html

The HP ProLiant BL620c G7 Server Blade offers unmatched scalability, performance, and economics in a two-processor Intel® Xeon® server blade. Two models are now available, one optimized for the Intel® Xeon® E7-2800 series and the other optimized for the Intel® Xeon® 6500/7500 series. Fully utilizing the design architecture of the Intel® Xeon® 7500 chipset, up to two top performing 130W processors are supported along with 32 RDIMM slots providing 1.0TB (BL620c G7 Intel Xeon E7-2800 models) and 512MB (BL620c G7 Intel Xeon 6500/7500 models) of memory for ultimate virtualization efficiency. The four included 10Gb FlexFabric converged network adapter ports with built-in autosensing 1Gb/10Gb Ethernet, FCoE, Flex-10, hardware-based accelerated iSCSI, iSCSI boot, and TCP/IP offload engine combined with the three PCIe Gen2 mezzanine expansion slots yield an outstanding 96Gb of total I/O bandwidth.

The BL620c G7 is also perfect for 2P applications requiring performance and features greater than typical dual processor (DP) Intel® Xeon® 5000 offerings. The scalability of the BL620c G7 offers up to 800% the memory capacity and increased memory performance along with an extensive list of memory RAS features, 2,000% the embedded Ethernet bandwidth, 400% the virtual machines (VMs), 300% the on-board I/O expansion slots, and 480% the total I/O bandwidth than other 2P Intel® Xeon® servers available today.

Traditional multi-processor (MP) class server blades are typically unbalanced providing processor performance and density at the expense of proportional memory capacity and I/O bandwidth. As such, these unbalanced servers fail when faced with larger databases and higher-density virtualization applications. Today, you have a better alternative. By designing a balanced architecture, the BL620c G7 is a very progressive 2P MP blade offering that ensures that all subsystems can be used effectively under a broad range of enterprise applications and workloads. The 2P BL620c G7 along with the 4P BL680c G7 together provide a complete Intel® Xeon® portfolio creating a new class of scale-up HP ProLiant server blades delivering the reliability and performance you need to handle demanding workloads with confidence.

• Processor:
  • One or two Intel® Xeon® E7-2800 Series processors each up to 10 cores and 130 watts (BL620c G7 Intel Xeon E7-2800 models)
    NOTE: All processors within the server must be identical.
  • One or two Intel® Xeon® 6500 or 7500 Series processors each up to 8 cores and 130 watts (BL620c G7 Intel Xeon 6500/7500 models)
    NOTE: All processors within the server must be identical.
  • Extensive list of over 35 system-wide reliability, serviceability, and availability (RAS) features: now including Double Device Data Correction (DDDC) Ready capability (BL620c G7 Intel Xeon E7-2800 models)
    NOTE: "Ready" is defined as the hardware is capable of supporting the feature with only a future planned software upgrade required to enable.
  • Intel® Advanced Encryption Standard New Instructions (Intel® AES-NI) delivering robust encryption without the need for additional appliances or increased performance overhead for improved encryption performance and efficiency (BL620c G7 Intel Xeon E7-2800 models)
  • Intel® Trusted Execution Technology (TXT) Ready for a more secure system by helping to detect and prevent malicious software attacks (BL620c G7 Intel Xeon E7-2800 models)
    NOTE: "Ready" is defined as the hardware is capable of supporting the feature with only a future planned software upgrade required to enable.
  • Intel® 7500 chipset with two integrated memory controllers per processor for maximum system performance
  • Intel 7510 Scalable Memory Buffer providing up to 1.8W (maximum) and 4.4W (idle) power savings per each SMI (BL620c G7 Intel Xeon E7-2800 models)
  • Intel Intelligent Power Technology including (BL620c G7 Intel Xeon E7-2800 models):
    • Lower partial active power that automatically pleases processor, memory, and I/O controller into the lowest available power states to meet the current workload while minimizing performance impact
    • Lower idle power that allows idling cores to be reduced to near-zero power independent of other cores, reducing server idle power consumption
  • Meshed network of four Intel® QuickPath Interconnects (Intel® QPI) each up to 6.4GT/s (25.6GB/s data bandwidth) for point-to-point high speed links increasing bandwidth and lowering latency
  • Intel® Hyper-threading resulting in higher processing throughput and improved multi-threaded application performance
  • Intel® Turbo Boost Technology that can automatically operate the processor(s) at a faster frequency than the base operating frequency under certain circumstances.
  • Up to 30MB of L3 cache per processors increasing efficiency of cache-to-cache data transfers maximizing memory bandwidth while reducing latency through storing greater amount of data thus reducing data transfers to memory.
  • Intel® Virtualization Technology that assist virtualization software in generating more efficient virtualization solutions.
  • PCI Gen2 increasing bandwidth up to 4 GB/s on each x8 PCI Express Gen2 connection.
    
• BL620c G7 Memory:
  • 1.0TB memory capacity via thirty-two (32) DDR3 registered DIMMs (RDIMM) slots operating up to 1066MHz (BL620c G7 Intel Xeon E7-2800 models)
    NOTE: The DDR3 memory speed is a function of the processor Intel® QPI speed. See the "Memory" section below for details.
  • 512MB memory capacity via thirty-two (32) DDR3 registered DIMMs (RDIMM) slots operating up to 1066MHz (BL620c G7 Intel Xeon 6500/7500 models)
    NOTE: DDR3 memory speed is a function of the processor Intel® QPI speed. See the "Memory" section below for details.
  • 8GB, 16GB and 32GB 1.35V DDR3L RDIMM low power memory options providing up to a 0.15V power savings per each DIMM compared to standard 1.5V DDR3 RDIMMs (BL620c G7 Intel Xeon E7-2800 models)
  • For maximum memory bandwidth, performance, and capacity, two integrated memory controllers per each processor that connect to a total of four Intel® Scalable Memory Buffers (SMB)
  • Memory RAS features including:
    • Data bus ECC protection and advanced ECC / SDDC
    • Demand scrubbing
    • DIMM address/control bus parity protection
    • Memory mirroring and memory failover
    • Rank sparring (online spare)
    • Intel® SMI lane and clock failover
    • Intel® SMI packet retry
    • Failed DIMM isolation
• Storage Controller:
  • Integrated SAS version 2.0 (6Gb) HP Smart Array P410i Controller with RAID 0 and 1.
    NOTE: The P410i is configured with no cache allowing the end user to select the desired cache option (if cache is desired in the first place).
  • P410i 512MB and 1GB flash backed write cache (FBWC) options
  • Optional Storage Works RAID mezzanine controllers (with BBWC and FBWC) for connection to external storage.
  • Two (2) slots for BBWC and/or FBWC battery options.
    NOTE: The server supports up to a combined total of two (2) battery cache options for the P410i and/or optional Storage Works RAID controllers.
  • Optional StorageWorks IO Accelerator cards for high performance I/O.
  • Optional P700m StorageWorks Controller for direct attach and shared SAS storage external to the c-Class enclosures
  • Optional HP D2200sb PCIe Storage Blade for direct attached and shared storage within the c-Class enclosures
• Internal Drive Support:
  • Two (2) hot-plug small form factor (SFF) drive bays
  • Support for SAS, SATA, and SSD hot-plug hard drives
• Network Controller:
  • Four (4) embedded HP NC553i 10Gb FlexFabric adapter ports supporting autosensing 10Gb/1Gb Ethernet, FCoE, Flex-10, TCP/IP offload engine, hardware-based accelerated iSCSI, and iSCSI boot.
    NOTE: Fibre Channel over Ethernet (FCoE) capability requires the use of an HP Virtual Connect FlexFabric 10Gb/24-port Module or HP 10GbE Pass-Thru Module.
    • The embedded adapter ports are routed interconnect bays 1 and 2 (c7000) and interconnect bay 1 (c3000)
  • One (1) 10/100 network adapter port dedicated to iLO 3 Management
• Mezzanine Support:
  • Three (3) mezzanine expansion slots as follows:
    • Two (2) Type II (25 watts) x8 PCIe Gen2; mezzanine slots 2 and 3 supporting QDR IB, 4Gb and 8Gb FC, 10Gb FlexFabric, 10Gb Flex10, 10GbE, 1GbE, I/O accelerator cards, the Storage Works RAID controllers, and the PCI Pass-thru Expansion card.
      • Mezzanine slot's 2 ports are routed to interconnect bays 5,6,7,8 (c7000) and 3,4,3,4 (c3000)
      • Mezzanine slot's 3 ports are routed to interconnect bays 7,8,5,6 (c7000) and 3,4,3,4 (c3000)
    • One (1) Type I (15 watts) x4 PCIe Gen2; mezzanine slot 1 supporting 4Gb and 8Gb FC, 10Gb FlexFabric, 10Gb Flex10, 10GbE, 1GbE, and the I/O accelerator cards
      • Mezzanine slot's 1 ports are routed to interconnect bays 3,4,3,4 (c7000) and 2,2,2,2 (c3000)
        
    • NOTE: HP recommends 10Gb adapters be installed in a x8 PCIe slot for optimal performance.
      
    • NOTE: Type II slots accept both Type I or Type II cards. Type I slots accepted Type I cards only.
• Expansion Blade Support:
  • Up to two HP BladeSystem Expansion Blades (Ultrium Tape Blades, PCI Expansion Blade, and Storage Expansion Blade) are supported using the HP PCI Expansion Pass-thru mezzanine Card. One HP PCI Express Mezzanine Pass-Thru Card is required per Expansion Blade.
    NOTE: The PCI Express Mezzanine Pass-Thru Card(s) must be installed in mezzanine slots 2 and/or 3.
    NOTE: In a c3000 rack enclosure where the blades are installed horizontally, up to two expansion blades may installed in the two slots created by the mini divider in the top half of the enclosure with a BL620c G7 installed in the lower half of the enclosure.
    NOTE: In a c3000 tower and c7000 rack enclosure where the blades are installed vertically, two expansion blades may installed in the blade slots adjacent to the BL620c G7 by staking one on top of another via a blade coupler that is included with the PCI Express Mezzanine Pass-Thru Card and the expansion blades. If a single expansion blade is installed, it must be installed in the lower slot adjacent to the BL620c G7; a half-height server may be installed above the expansion blade.
    
• Internal USB and SD Support:
  • One (1) internal USB 2.0 connector for USB flash media drive keys
  • One (1) internal micro secure digital high capacity (SDHC) card slot
• Trusted Platform Module (TPM):
  • One (1) internal TPM 1.2 module connector
• Infrastructure Management:
  • This server blade requires the latest version of the Onboard Administrator firmware. This firmware release may also require other subsystem firmware upgrades. For information on the latest firmware versions, please see the Blades Firmware Maintenance website at: https://h18004.www1.hp.com/products/blades/components/c-class-compmatrix.html
  • HP Integrated Lights-Out 3 (iLO 3) management processor for simplified server setup, health monitoring and recovery, power and thermal control, and lights-out remote administration.
  • HP Insight Control, a product option, delivers essential infrastructure management that can help save time and money by making it easy to deploy, monitor, control and optimize your IT infrastructure through a single, simple management console. Insight Control supports both Windows and Linux-based central management servers.
  • HP Insight Dynamics for ProLiant, a product option, is an integrated command center that enables IT Staff personnel to continuously analyze and optimize a converged infrastructure, while automating and reducing the cost of common data center tasks by as much as 40 percent. This ultimately enables them to dynamically keep pace with the organization's changing business requirements.
• Operating System Support:
  • Microsoft Windows, RHEL, SLES, Oracle Solaris, VMware, and Citrix XenServer
• Form Factor:
  • Full height, single wide server blade that plugs into the HP BladeSystem c3000 and c7000 enclosures
• Enclosures:
  • HP offers two different c-Class server blade enclosures to meet your individual needs:
    • The HP BladeSystem c7000 rack enclosure is 10U high and holds up to 8 HP ProLiant BL620c G7 servers plugged vertically.
    • The HP BladeSystem c3000 rack enclosure is 6U high and holds up to 4 HP ProLiant BL620c G7 servers plugged horizontally.
  • Server blades, storage blades, and interconnect modules are all designed to fit into the c7000 and c3000 enclosures.
  • For additional enclosure information, please see: https://h18004.www1.hp.com/products/blades/components/enclosures/c-class/index.html.
• Warranty:
  • This product is covered by a global limited warranty and supported by HP Services and a worldwide network of HP Authorized Channel Partners resellers. Hardware diagnostic support and repair is available for three years from date of purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to warranty services are available through HP Care Pack services or customized service agreements. Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.
    NOTE: Server warranty includes 3 year Parts, 3 year Labor, 3-year on-site support. Warranty repairs may be accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity. Customers may choose to have HP replace Optional CSR parts at no charge. Additional information regarding worldwide limited warranty and technical support is available at: https://h18004.www1.hp.com/products/servers/platforms/warranty/index.html

Four (4) integrated HP NC553i 10Gb FlexFabric adapter ports supporting 10Gb/1Gb autosensing Ethernet, FCoE, Flex-10, TCP/IP offload engine, hardware-based accelerated iSCSI, and iSCSI boot.

Three (3) mezzanine expansion slots as follows:

• Two (2) Type II (25 watts) x8 PCIe Gen2
• One (1) Type I (15 watts) x4 PCIe Gen2

NOTE: Type II slots accept both Type I or Type II cards. Type I slots accepted Type I cards only.

Integrated SAS version 2.0 (6Gb) HP Smart Array P410i Controller with RAID 0 and 1.
NOTE: The P410i is configured with no cache allowing the end user to select the desired option (if cache is desired in the first place).
P410i 512MB and 1GB flash backed write cache (FBWC) options.
Optional Smart Array RAID mezzanine controllers (with BBWC and FBWC) for connection to external storage.
NOTE: The server supports up to a combined total of two (2) battery cache options for the P410i and/or optional Storage Works RAID controllers.
Optional StorageWorks IO Accelerator cards for high performance I/O.
Optional HP StorageWorks D2200sb PCIe Storage Blade for direct attached and shared storage within the c-Class enclosures

Up to three (3) optional 4Gb and/or 8Gb Fibre Channel HBA mezzanine adapters (Brocade, Emulex and QLogic options).

HP ProLiant BL620c G7 server blades are optimized for HP StorageWorks MSA, EVA, and XPHP and are compatible with select third party SANs. See the blade storage page for more details at https://h18004.www1.hp.com/products/blades/components/c-class-sans.html.

Managing the growing number of servers can be complex and expensive for your organization. IT managers need to address changing business needs with tools that meet the challenges of managing today's complex Datacenters.

HP provides management solutions that are designed to simplify a server's installation, configuration and maintenance throughout the entire server lifecycle. This provides the customer with higher levels of operational efficiency and highly reliable systems: www.hp.com/go/foundation.

The foundation pack includes:

• HP SmartStart
• HP Management DVD
• HP ProLiant Smart Update Firmware DVD
• SmartStart version supported (minimum): SmartStart 8.60.
  https://www.hp.com/servers/smartstart

NOTE: In an effort to support reducing our environmental impact, the HP Insight Foundation Suite for ProLiant media will be available as a selectable option for this server at time of order of a Factory Integrated Model. This will allow customers to order the number of media kits that best meet their needs and eliminate receiving unnecessary duplicate media.

HP Cluster Platforms are specifically engineered, factory-integrated large-scale ProLiant clusters optimized for High Performance Computing, with a choice of servers, networks and software. Operating system options include specially priced offerings for Red Hat Enterprise Linux and Novell SLES, as well as Microsoft Windows HPC Server. A Cluster Platform Configurator simplifies ordering. https://www.hp.com/go/clusters

Microsoft Windows Server
Red Hat Enterprise Linux (RHEL)
SUSE Linux Enterprise Server (SLES)
Oracle Solaris
VMware Server
Citrix XenServer

NOTE: For more information on HP's Certified and Supported ProLiant Servers for OS and Virtualization Software and latest listing of software drivers available for your server, including how to purchase from HP, please visit our OS Support Site at: https://www.hp.com/go/supportos and our driver download page https://www.hp.com/support/BL620cG7.

BL620c G7 Memory

• HP Memory Quarantine (Intel MCA Recovery) Ready. In conjunction with the operating system support, allows a server to recover from uncorrectable memory errors which would have otherwise caused a system crash. (BL620c G7 Intel Xeon E7-2800 models).
• Double Device Data Correction (DDDC) Ready. DDDC provides the ability to save a DIMM from being replaced due to a bad dram device (BL620c G7 Intel Xeon E7-2800 models).
• Data Bus ECC protection for automatic correction from a single data bit error and detection of double data error bits.
• Advanced ECC/SDDC provides continued memory operation in the event of a single memory device failure and allows removal of a single DRAM from the memory map if it exhibits a failure and recovers its data into a new device.
  • Supports for both x4 and x8 Intel® SDDC.
• Demand Scrubbing writes corrected data back to the memory once a correctable error is detected on a read transaction.
• DIMM Address/Control Bus Parity Protection provides a means to detect and protect command and address errors.
• Memory Failover uses a mirrored DIMM once a failed DIMM in a mirrored set is detected.
• Memory Mirroring provides a copy of memory stored with dynamic failover in case of failure within socket (intra-socket) memory mirroring.
  • The system will operate in non-hemisphere mode when mirroring is enabled.
• Rank Sparring (On Line Spare) provides dynamic failover to a spare DIMM rank or spare rank pair behind the same memory controller. Cannot be enabled concurrently with memory mirroring.
  NOTE: HP offers the rank sparing rather than DIMM sparing as rank sparing uses less spare memory resulting in less overhead.
• Failed DIMM Isolation identifies a specific failing DIMM lockstep pair thereby enabling the user to replace only the failed DIMM pair. Identifies a single DIMM for correctable errors and DIMM pair for uncorrectable errors.

Virtualization

• Intel® VT-x (FlexMigration, FlexPriority, and Extended Page Tables) provides:
  • Platform control between the VMM and guest OSs for faster, more reliable and secure transfers.
  • VM migration features that enhance flexibility for failover, load balancing, disaster recovery, and maintenance.
• Intel® VT-x Real Mode & Pause Loop Exiting (BL620c G7 Intel Xeon E7-2800 models):
  • Real Mode allows guests to operate in real mode, removing the performance overhead and complexity of an emulator.
  • Pause Loop Exiting provides detection of spin locks in guest software and helps avoid lock-holder preemption to reduce overhead and improve performance.
• Intel® VT-d (Intel® Virtualization Technology for Directed I/O) enables the VMM to assign specific I/O devices to specific guest OSs improving security and availability.

Mezzanine options and I/O

• Optional dual-port Fibre Channel mezzanine cards for redundant SAN connections.
• Optional dual-port InfiniBand mezzanine cards for redundant high performance connections.
• Four embedded Ethernet adapter ports for redundant LAN connections.
• Multiple mezzanine I/O expansion slots each supported multiple data paths routed to redundant interconnect modules.
• Network Adapter Teaming (Bonding) provides network fault tolerance, transmit load balancing, and switch-assisted load balancing.

Processor/Chipset

• Processor Internal Sensors & Thermal Control protection against over-temperature conditions.
• Cache parity/ECC protects cache data from accidental data corruption due to particle hits.
• Machine Check Architecture (MCA) detects and captures hardware errors such as system bus, ECC, parity, cache, other.
• Enhanced MCA handling & error logging builds upon the original Machine Check Architecture to: offers more "banks" and increased "resolution" for reporting errors that cause MCA events and 2) sets check flags for the OS to poll.
• External Bus Error Recovery (ECC) enables automatic correction from a single data bit error and detection of double data error bits on the memory data bus.
• Corrupt Data Containment tags faulty data before it is consumed (often called data poisoning) to limit the impact to the currently running program and to greatly reduce the need to reset the system.
• On-Die Error Protection protects registers from particle hits.

Storage

• Two hot-plug SAS/SATA/SSD drive bays.
• Integrated HP Smart Array P410i Controller with RAID 0 and 1 standard
• Integrated HP Smart Array P410i Controller upgradeable firmware with recovery ROM capability
• HP Smart Array P410i flash backed write cache (FBWC) options to 1GB.
• Optional multiple Smart Array RAID mezzanine controllers (with BBWC and FBWC) for direct attach and shared SAS storage external to the c-Class enclosure.
• Optional HP D2200sb Storage Blade for direct attached and shared storage within the c-Class enclosure.

Intel® QuickPath Interconnect (QPI)

• QPI Link Retry restarts as cycle when a failure is detected on the link.
• QPI Clock Failover redirects the forwarded clock to one of the two failover clock lanes in the event of a forwarded clock failure.
• QPI Self-Healing enables a QPI link to map a failed lane and downshift from full to ½ width (or ½ width to ¼ width) QPI link if there are errors on the link.
• QPI Cycle Redundancy Checking (CRC) automatically detects data errors using a checksum of either 8 bits or 16 bits.
• QPI Poisoning tags an erroneous packet with a "poisoned bit" on the QPI fabric.
• QPI Lane Failover identifies a faulty lane within data paths removing them from operation reducing command/address errors.

Server Blade Enclosure Infrastructure

• Up to 10 hot-plug redundant Active Cool fans per enclosure.
• Up to 6 hot-plug high efficiency redundant power supplies per enclosure.
• Dual grid power providing redundant rack enclosure power feeds to the enclosure.
• Up to eight interconnect modules per enclosure providing four simultaneous redundant fabrics for FlexFabric, Virtual Connect Ethernet, Fibre Channel, InfiniBand, iSCSI, SAS, etc.
• Optional enclosure redundant Onboard Administrator system management module.

• ACPI 2.0 Compliant
• PCI 2.2 Compliant
• Microsoft® Logo certifications
• USB 2.0
• Secure Digital 2.0
• TMP 1.2
• IEEE (see the NC553i Technical Specifications section)
• Advanced Encryption Standard (AES)
• Triple Data Encryption Standard (3DES)
• SNMP
• SSL 2.0
• Active Directory v1.0 (Windows 2003)
• IPMI 2.0
• DMTF Systems Management Architecture for Server Hardware Command Line Protocol (SMASH CLP)

• Intel® AES-NI (BL620c G7 Intel Xeon E7-2800 models)
• Intel® Trusted Execution Technology (TXT) Ready (BL620c G7 Intel Xeon E7-2800 models)
• Power-on password
• Administrator's password
• Integrated Lights-Out 3 with:
  • 12 customizable user accounts
  • SSL encryption
  • Secure Shell version 2
  • Advanced Encryption Standard (AES) and Triple Data Encryption Standard (3DES) on browser, CLP and XML scripting interface
  • AES and RC4 encryption of video
    
  • Disable via a global setting
    
• Keyboard password
• External USB port enable/disable
• Network server mode
• Serial interface control
• TPM (Trusted Platform Module) 1.2 option

HP Factory Express offers configuration, customization, integration and deployment services for HP servers and storage products. Customers can choose how their factory solutions are built, tested, integrated, shipped and deployed.

Factory Express offers service packages for simple configuration, racking, installation, complex configuration and design services as well as individual factory services, such as image loading, asset tagging, and custom packaging. HP products supported through Factory Express include a wide array of servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem, HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable network switches.

For more information on Factory Express services on your specific server model please contact your sales representative or go to: https://www.hp.com/go/factory-express.

HP Technology Services for Industry Standard Servers and BladeSystem
Capitalizing on HP ProLiant server and HP BladeSystem capabilities requires a service partner who understands your increasingly complex business technology environment. That's why it makes sense to team up with the people who know HP infrastructure hardware and software best - the experienced professionals at HP Services.

What HP ProLiant and BladeSystem Services can do for you
HP ProLiant and BladeSystem Services can help you design, deploy, test, integrate, support, and manage IT and infrastructure solutions. This way, HP proposes services solutions that include more than just uplift of base warranty. You can get the support you need by choosing from one of a number of service packaged solutions we have designed to address wider set of customer support needs.

HP Technology Services meets business challenges with services offered in three packages
Optimized Care Package, Standard Care Package, and Basic Care Package - available for each product group. Such packaged solutions enable customers to optimize technology operations, minimize risk and drive better business outcomes with easy-to-buy, easy-to-use scalable support packages for servers, storage, networking and software.

Supports maintaining servers at optimum performance availability

HP Installation and Startup Service for HP BladeSystem c-Class Infrastructure for c3000/c7000 enclosure
Provides for the installation and startup of a BladeSystem c3000 Infrastructure in a single blade enclosure including hardware and software, including deployment of OS, HP SIM, RDP, RDP, PMP and VPM.
https://h20195.www2.hp.com/V2/GetPDF.aspx/4AA0-5964ENW

3-Year HP Critical Advantage for c3000/c7000 enclosure + 3-Year HP Critical Advantage for Blade server
Provides end-to-end infrastructure support solution for business critical applications running on virtualized/x86 infrastructures, enabling the customers to cost effectively build, operate, and continuously improve their IT environment. https://h20195.www2.hp.com/V2/GetDocument.aspx?docname=4AA3-1772ENW

HP Installation and Startup Service for HP BladeSystem c-Class Enhanced Network
HP Provides for the configuration and testing of BladeSystem Ethernet interconnect switches to facilitate proper implementation of network protocols and access to advanced features.
https://h20195.www2.hp.com/V2/GetPDF.aspx/4aa0-5969ENW

Additional Services: Virtualization Services - Strategy, Design, Transition, Operation, Continual Service Improvement.

Delivers minimum recommended support service level

HP Installation and Startup Service for HP BladeSystem c-Class Infrastructure for c3000/c7000 enclosure
Provides for the installation and startup of a BladeSystem c3000 Infrastructure in a single blade enclosure including hardware and software, including deployment of OS, HP SIM, RDP, RDP, PMP and VPM.
https://h20195.www2.hp.com/V2/GetPDF.aspx/4AA0-5964ENW

3-Year, HP 24x7 4 hour Response, Hardware Support Onsite Service for c3000/c7000 enclosure + 3-Year, HP 24x7 4 hour Response, Hardware Support Onsite Service for Blade server
Provides you with rapid remote support and if required an HP authorized representative who will arrive on site any time and day of the year to begin hardware maintenance service within 4 hours of the service request being logged.
https://h20195.www2.hp.com/V2/GetPDF.aspx/5982-6547EEE

3-Year , HP 24x7 Software Support for Insight Control
Provides for the deployment and basic configuration of HP Insight Control on HP ProLiant ML and DL series servers or HP BladeSystem servers.
https://h20195.www2.hp.com/V2/GetPDF.aspx/5981-6645EEE.pdf

Additional Services - Startup Blade System c-Cass Enhanced Network Service; Software OS (Microsoft, Linux (SUSE/Red Hat) & VMware Installation & Start Up and Software Support); +30 Proactive Select Credits, Factory Express.

The packages include HP Insight Remote Support that uses proven technology to deliver secure, reliable 24x7 remote monitoring, diagnoses, and problem resolution. It is available at no additional cost to all warranty, HP Care Pack Service, and service agreement customers.

To learn more on HP ProLiant servers and HP BladeSystem servers, please contact your HP sales representative or HP Authorized Channel Partner. Or visit: www.hp.com/services/bladesystem

HP ProLiant BL620c G7 E7-2860 1P 32GB-R Server
643763-B21

HP ProLiant BL620c G7 E7-2850 1P 32GB-R Server
643764-B21

HP ProLiant BL620c G7 E7-2830 1P 32GB-R Server
643765-B21

Four (4) integrated HP NC553i 10Gb FlexFabric adapter ports supporting 10Gb/1Gb autosensing Ethernet, FCoE, Flex-10, TCP/IP offload engine, hardware-based accelerated iSCSI, and iSCSI boot
One (1) 10/100 network adapter port dedicated to iLO 3 Management

HP ProLiant BL620c G7 X6550 1P 8GB-R P410i Hot Plug SAS/SATA 2 SFF Server
588964-B21

HP ProLiant BL620c G7 E6540 1P 8GB-R P410i Hot Plug SAS/SATA 2 SFF Server
588965-B21

HP ProLiant BL620c G7 E7530 1P 8GB-R P410i Hot Plug SAS/SATA 2 SFF Server
588963-B21

HP ProLiant BL620c G7 E6510 1P 8GB-R P410i Hot Plug SAS/SATA 2 SFF Server
588966-B21

Four (4) integrated HP NC553i 10Gb FlexFabric adapter ports supporting 10Gb/1Gb autosensing Ethernet, FCoE, Flex-10, TCP/IP offload engine, hardware-based accelerated iSCSI, and iSCSI boot
One (1) 10/100 network adapter ports dedicated to iLO 3 Management

Four (4) integrated HP NC553i 10Gb FlexFabric adapter ports supporting 10Gb/1Gb autosensing Ethernet, FCoE, Flex-10, TCP/IP offload engine, hardware-based accelerated iSCSI, and iSCSI boot

One (1) 10/100 network adapter port dedicated to iLO 3 Management

One (1) Integrated SAS version 2.0 (6Gb) HP Smart Array P410i Controller with RAID 0 and 1
NOTE: The P410i is configured with no cache allowing the end user to select the desired cache option (if cache is desired in the first place).

Two (2) cache slots for BBWC and/or FBWC battery options.
NOTE: The server supports up to a combined total of two (2) battery cache options for the P410i and/or optional Storage Works RAID controllers.

Two (2) small form factor hot-plug SAS/SATA/SSD hard drive bays

Three (3) I/O expansion slots

One (1) integrated Lights-Out 3

Integrated USB, MicroSDHC, and TPM connectors

NOTE: Standard memory configurations listed do not apply to "Factory Integrated Models."

Memory Subsystem Architecture
For maximum memory bandwidth, performance, and capacity, each Intel® Xeon® E7-2800 and 6500/7500 series processor socket contains two memory controllers. Each memory controller has two Intel Scalable Memory Interface (SMI) buses operating in lockstep for a total of four SMIs per processor. Each SMI in turn bus connects to an Intel® Scalable Memory Buffer (SMB). The purpose of the memory buffer is to convert the SMI to DDR3. Each of the four memory buffers has two DDR3 channels that support four RDIMMs each for a grand total of sixteen RDIMMs per installed processor (32 total RDIMMs per BL620c G7 server).

Maximum memory capacity is a function of the server model:

• The BL620c G7 server models supporting Intel Xeon E7-2800 processors includes the new Intel® 7510 Scalable Memory Buffer supporting up to 32GB DDR3 RDIMMs providing 1.0TB of memory (32GB RDIMMs x 32 DIMM slots).
• The BL620c G7 server models supporting Intel Xeon 6500/7500 processors support up to 16GB DDR3 RDIMMs providing 512MB of memory (16GB RDIMMs x 32 DIMM slots).

All RDIMMs will operate at the highest possible speed for a given processor. Memory speed is not affected by number of RDIMMs or ranks. However, memory speed is a function of the processor QPI bus speed per the following:

• Processors with a QPI speed of 6.40GT will operate memory at 1066MHz
• Processors with a QPI speed of 5.86GT will operate memory at 978MHz
• Processors with a QPI speed of 4.80GT will operate memory at 800MHz

DDR3 and DDR3L Memory Population Guidelines
An overview of the RDIMM installation guidelines are summarized below. For detailed memory configuration rules and guidelines, please see the BL620c G7 user guide at: www.hp.com/support and the Online DDR3 Memory Configuration Tool at: www.hp.com/go/ddr3memory-configurator.

1. Install only HP BL620c G7 supported DDR3 and DDR3L RDIMMs.
2. RDIMMs must be installed for processor 1.
3. Populate RDIMM slots for a processor only if the processor is installed.
4. To maximize performance in multi-processor configurations, distribute the total memory capacity between all processors as evenly as possible.
5. The minimum configuration is two RDIMMs installed on processor 1.
6. RDIMMs must be installed in pairs with identical characteristics. When possible, for configuration simplicity, HP recommends using RDIMMs with identical part numbers throughout the system.
7. For best performance, HP recommends that RDIMM pairs be populated in sequence by letter designation. Install RDIMM pair (4A, 5A) first, followed by RDIMM pair (12B, 16B), RDIMM pair (2C, 7C), RDIMM pair (10D, 14D), RDIMM pair (3E, 6E), RDIMM pair (11F, 15F), and RDIMM pair (1G, 8G).
8. When installing mixed rank RDIMMs for any processor, RDIMMs with the highest number of ranks must be installed in the white RDIMM connector locations. This guarantees proper electrical signaling on the DDR3 channel since RDIMMs with higher rank counts present larger electrical loading on the DDR3 channel and must be populated at the end point of the channel.
9. 1.5V DDR3 and 1.35V DDR3L RDIMMs may be installed within the same socket. In this case, all RDIMMs on that socket will operate at 1.5V.
10. The BL680c G7 supports memory hemisphere mode (for a high-performance memory interleaving technology) as well as several advanced memory modes (AMP) including advanced ECC, online spare, and mirrored memory. Please see the BL680c G7 user guide at: www.hp.com/support for a description of each of these features and their memory configuration guidelines.
11. There are several additional recommended steps for memory performance optimization, please see the BL680c G7 user guide at: www.hp.com/support for a complete list.

Power Specifications

For power specifications including input requirements, BTU rating, and power supply output, please see the HP BladeSystem c-Class Enclosures QuickSpecs located at:
HP BladeSystem c3000 Enclosure QuickSpecs:
https://h18000.www1.hp.com/products/quickspecs/12790_na/
12790_na.html
HP BladeSystem c7000 Enclosure QuickSpecs:
https://h18000.www1.hp.com/products/quickspecs/12810_na/
12810_na.html

To review typical system power ratings use the HP BladeSystem Power Sizer available at: https://www.hp.com/go/bladesystem/powercalculator.

System Inlet Temperature

• ProLiant Teaming including Network Fault Tolerance, Transmit Load Balancing, and Switch-Assisted Load Balancing
• 9K Jumbo frames (4K Jumbo frames when in FCoE mode)
• Microsoft Windows Receive Side Scaling (RSS)
• FCoE or accelerated iSCSI mode
• iSCSI boot
• Flex-10 support
• TCP/IP offload engine
• 10Gb Ethernet ort 1Gb Ethernet autosensing
• Microsoft TCP chimney compliant
• Supports 8 Physical Functions (PF)
• Supports 128 Virtual Functions (VF):
  • Up to 32 VFs per PF
  • Support 128 MAC address
• Traffic Shaping and QoS across each VF and PF:
• NIC Fine-grain QoS 10 Mbps to 10Gbps in steps of 10Mbps
• HBA fine-grain QoS 1000 IOPs to 500,000 IOPs in steps of 1000 IOPS
• On-chip VM-VM switching
• Traffic steering and isolation
• Hardware based filtering for 128 VLANIDs with QinQ tag filtering
• Protection against denial-of-service attacks & malfunctioning VMs

Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling programs in many geographic areas. For trade-in information, please go to: https://www.hp.com/go/green. To recycle your product, please go to: https://www.hp.com/go/green or contact your nearest HP sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.

The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each product type for use by treatment facilities. This information (product disassembly instructions) is posted on the Hewlett Packard web site at: https://www.hp.com/go/green. These instructions may be used by recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP equipment.