Optional Right Power Buttons, Health LEDs and UID bezel

• New high efficiency power supplies.
• New low voltage UDIMM

• Half Height Nodes (1U): One available PCI Express Gen 2.0 slots: (standard on 4-node BTO model).
  • Slot 1: Low profile PCI-Express 2.0 x16
• Full Height Nodes (2U): three available riser options:
  • Option 1: Up to three available PCI-Express Gen 2.0 slots:
    • Slot 1: full-length/full-height PCI-Express 2.0 x16
    • Slot 2: full-length/half-height PCI-Express 2.0 x4
    • Slot 3: low-profile PCI-Express 2.0 x4
  • Option 2: Up to three available PCI-Express Gen 2.0 slots:
    • Slot 1: full-length/full-height PCI-Express 2.0 x8
    • Slot 2: full-length/half-height PCI-Express 2.0 x8
    • Slot 3: low-profile PCI-Express 2.0 x8
  • Option 3: Up to two available PCI-Express Gen 2.0 slots: (standard on 2-node BTO model)
    • Slot 1: full-length/full-height PCI-Express 2.0 x16
    • Slot 2: low-profile PCI-Express 2.0 x8

3.3 volts

1 rear per server node (Optional front UID per chassis)

Integrated Matrox Graphics G200e, 32MB Standard

• 16 bit color: maximum resolution of 1600 x 1200
• 32 bit color: maximum resolution of 1280 x 1024

The following NVIDIA graphics cards are supported in the DL1000:

• NVIDIA Quadro FX5800 512MB PCIe x 16 graphics card

NOTE: For more information on the latest visualization and acceleration qualification status, please see https://www.hp.com/go/accelerators.
NOTE: An HP DL170h Graphics Bracket/Cable Kit (P/N 536860-B21) is required when installing this NVIDIA card. The FX5800 can only be installed in the 2 slot full-height riser option: HP DL170h I/O Riser PCIe x16 x8 FIO option (P/N 512481-B21).

One 6' Highline (IEC-IEC) power cord ships standard
NOTE: HP ProLiant DL servers are primarily connected to PDU's in data center racks so they ship standard with only a PDU power cord (416151-B21). If a user wishes to power a ProLiant DL server using a 110V receptacle (NEMA-15), the NEMA power cord (227099-001) must be ordered separately.

NOTE: Japan BTO and CTO configurations get the 6' 4165151-291 power cord in addition. China BTO and CTO configurations get the 6' 416151-AA1 power cord in addition.
NOTE: If customers require a local power cord, they can check the power cord matrix for the appropriate cord. Please see the following power cord matrix: https://www.hp.com/go/powercordmatrix

In addition to the efficiencies gained by the shared power infrastructure, the DL1000 contains advanced power metering and capping capabilities. The embedded Power Management Controller (PMC) is able to monitor power consumption and throttle the speed of the processors and memory in each node within the chassis in order to maintain a pre-set power budget. HP provides a simple command-line utility, called HP ProLiant Power Interface Control (PPIC) Utility, for reading and configuring the power control logic of the server nodes. Versions are available for MS Windows Server OS (2008 and 2008 R2) and Linux OS (RHEL5 and SLES11) with the requirement that the OS IPMI Driver be installed. The following Power Management modes for power redundancy are standard and are configurable in the controller:

• No Redundancy - power control disabled. No power throttling will occur.
• (DEFAULT) AC Redundancy with Throttling. This mode allows all nodes to share both power supplies and run at maximum performance. Power control logic will only throttle the performance of each node when the power draw by the chassis attempts to exceed the load supported by the power supplies. In this mode, the box is expected to survive an unexpected AC Power loss to one of the power supplies.
• Full AC/DC Redundancy - power control logic will maintain a power cap value for the chassis at the DC rating of a single power supply (750W, or 1200W), such that if one power supply experiences a DC or AC failure, the chassis should remain on-line and operational.

Dynamic Power Capping is included with the LO100 Advanced Pack:

• Dynamic Power Capping - User specifies the power envelope for the 2U chassis, within the capabilities of the hardware installed. Users run a utility to calibrate the minimum and maximum power consumption envelope for the chassis. In order to avoid any impact to performance due to throttling, a User selectable Power Cap value should not be set below the minimum power value provided by the utility.

HP has a new design for ProLiant power- the new Common Slot Power Supply bay. This design provides the customer with commonality in power supplies across multiple platforms to save on the cost of spares and allows HP to offer multiple power solutions to fit the customers' needs. Many HP ProLiant Servers come with Common Slot, High Efficiency and Right-Size Power Supplies. The new HP Common Slot power supplies are designed for the highest power efficiency without degrading performance of the ProLiant server. Power Supplies have efficiency ratings up to 94%. There are multiple Right Size power options available depending on the configuration of your server. To make sure you select the correct power supply to meet your configuration, please use the HP Power Advisor at: www.hp.com/go/proliant-energy-efficient or www.hp.com/go/hppoweradvisor. All HP Common Slot power sources are UL, CE Mark Compliant, Hot Plug and Redundant.

There is a low cost, Industry Standard 1500W (2x750W) Power Supply option that does not support hot-pluggability, redundancy or power capping functionality.

NOTE: Mixing of power supplies in the same chassis is not supported. All power supplies must be of the same type, all 460W, all 750W 94%, all 750W 92%, all 1200W 94%, or all 1200W 90%. If non-matched power supplies are inserted you will get errors and operation will fail.

It is highly recommended that you use the HP Power Advisor in defining the "Right-Size" power supply for your needs. HP offers several Common Slot Power Supply Options for this platform. HP's ProLiant Common Slot Power supplies meet multiple Energy Efficiency Initiatives.

NOTE: The 80 PLUS program is a unique forum that unites electric utilities, the computer industry, and consumers in an effort to bring energy efficient technology solutions to the marketplace. 80 Plus independently tests power supply efficiency and publicly posts the results on 80Plus.org.
Optional power supplies can be purchased through power supply option kits (see Power Supply Options for part numbers).

For required cabling information, refer to the HP Web site at: www.hp.com/servers/dl170h.

HP offers two different drive cages for the 2U HP ProLiant h1000 G6 Chassis: 8 LFF HDD Cage or 16 SFF HDD Cage.

The 2U chassis can support three server node configurations:

• Two full height nodes
• One full height node and two half-height nodes
• Four half-height nodes

HP Lights-Out 100 with Optional LO100 Advanced Licenses for Virtual KVM and Virtual Media.

Standard Features:

• IPMI 2.0 & SMASH CLP support
• ROM Setup Utility
• Improvements to virtual media with the addition of USB 2.0 drives and protocol support for much faster transfer speeds and DVD-ROM support plus simplified virtual media (floppy and CD with no FTTP server requirements)
• Enhanced browser interface and embedded KVM over IP provides OS-independent remote graphical console
• 24x7 Technical Support and Update (TSU) 1 year support and license upgrades included in Advanced license

For more information, see: www.hp.com/go/lo100.

This product is covered by a global limited warranty and supported by HP Services and a worldwide network of HP Authorized Channel Partners. Hardware diagnostic support and repair is available for one year from date of purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to warranty services are available through HP Care Pack services or customized service agreements. Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.
NOTE: Server Warranty includes 1 year Parts, 1 year Labor, 1-year on-site support with next business day response. Warranty repairs may be accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity. Customers may choose to have HP replace Optional CSR parts at no charge. Additional information regarding worldwide limited warranty and technical support is available at: https://h18004.www1.hp.com/products/servers/platforms/warranty/index.html.

HP Insight Control for Linux

HP provides management solutions that are designed to simplify a server's installation, configuration, and maintenance throughout the entire server lifecycle. This provides the customers with higher levels of operational efficiency and highly reliable systems.

While ProLiant 100 series G6 servers do not support the Insight Foundation Suite for ProLiant, they support a key subset of this important suite software tools and utilities which are very suitable for this class of server: SIM, SMH, agents, providers, and a SmartStart 'like' deployment CD called Easy Set-up which greatly simplifies server set-up. Additionally the DL100 and SL100 G6 models support the SmartStart Scripting Toolkit (SSSTK), an automated scalable deployment utility.

Information on core management supported on ProLiant 100 series G6 servers can be found at these URLS:

• Core Management: www.hp.com/go/coremanagement
• HP ProLiant 100 series Easy Set-up CDs: www.hp.com/servers/easysetup

HP Insight Management Agents and Insight Management Providers are available for HP Systems Insight Manager (SIM) Integration.

ProLiant 100-series G6 servers can use the same SNMP based Insight Management Agents supported by other ProLiant servers. As a result, administrators can use HP Systems Insight Manager (SIM) 5.3 and greater to manage ProLiant 100-series G6 servers. Administrators can also use any other SNMP- based management tool. These agents are obtained as part of the ProLiant 100-series model-specific "Easy Set-up" CDs, or through https://www.hp.com/servers/easysetup

The following capabilities are enabled on the 100-series G6 servers by the SNMP agents:

• Health monitoring capabilities, including monitoring for drives, fans, network, power supplies, and temperature
• Alerting capabilities, including basic alert notification for Smart Array drive pre-failure only
• Performance monitoring capabilities providing information on processor, memory, disk free space, network utilization

For additional information, please see: https://www.hp.com/go/insight

Easy Set-up CDs are available on all 100-series G6 servers and are also available as an ISO image web download. HP ProLiant Easy Set-up CDs provide easy, step-by-step, single and multi-server server utilities for the ProLiant 100-series G6 servers to streamline server setup for 100-series G6 servers. The user experience is consistent with SmartStart and offers the following capabilities:

• Boot environment and GUI
• Assisted Installation: Windows 2003 Server and Windows 2008 Server drivers
• Manual installation: Windows 2003 Server, Windows 2008 Server, and Linux drivers (specific OS support varies by server. Refer to each server's QuickSpecs for supported versions)
• HP Insight Diagnostics
• AutoRun
• Array Configuration Utility (ACU) has been combined with Array Diagnostics Utility (ADU) to offer both configuration of array controllers and storage devices and testing of array controller hardware
• SmartStart Scripting Toolkit (SSSTK) and Smart Components for software and drivers

NOTE: OS and SW available for Manual Installation are listed on each servers' QuickSpecs.

Subscriber's Choice

Subscriber's Choice Driver and Support Alerts/Notifications is a web-based email subscription service that provides software and driver change notifications for ProLiant products. Sign up at: https://www.hp.com/go/subscriberschoice and customize your profile to receive various new alerts as they become available, on a weekly or monthly basis.

The latest software, drivers, and firmware fully optimized and tested for your ProLiant server and options; downloaded from Software and Drivers download pages website at: https://www.hp.com/go/support and from www.hp.com/servers/easysetup. Contains the following:

• HP Insight Management Agents for Systems Insight Manager (SIM) Integration
  
• HP Systems Management Homepage
  
• Array Configuration Utility (ACU)
  
• Array Diagnostics Utility (ADU)
  
• HP Insight Diagnostics

The HP eConfigure Enterprise Configurator now provides factory default racking for our HP hardware portfolio. This approach is aligned with our strategic direction to meet the needs and expectations of our valued customers. If you require "custom" rack configuration, please contact HP's Customer Business Center or an Authorized Partner for assistance. https://www.hp.com/products/configurator

HP Technology Services for Industry Standard Servers and BladeSystem
Capitalizing on HP ProLiant server and HP BladeSystem capabilities requires a service partner who understands your increasingly complex business technology environment. That's why it makes sense to team up with the people who know HP infrastructure hardware and software best - the experienced professionals at HP Services.

What HP ProLiant and BladeSystem Services can do for you
HP ProLiant and BladeSystem Services can help you design, deploy, test, integrate, support, and manage IT and infrastructure solutions. This way, HP proposes services solutions that include more than just uplift of base warranty. You can get the support you need by choosing from one of a number of service packaged solutions we have designed to address wider set of customer support needs:.

HP Technology Services meets business challenges with services offered in three packages - Optimized Care Package, Standard Care Package, and Basic Care Package - available for each product group. Such packaged solutions enable customers to optimize technology operations, minimize risk and drive better business outcomes with easy-to-buy, easy-to-use scalable support packages for servers, storage, networking and software.

Basic Care Package: delivers minimum recommended support service level

HP ProLiant Server Hardware Installation
Provides for the basic hardware installation of HP branded servers, storage devices and networking options to assist you in bringing your new hardware into operation in a timely and professional manner
https://h20195.www2.hp.com/V2/GetPDF.aspx/5981-9356EN

HP Installation and Startup for Insight Control Software
Provides for the deployment and basic configuration of HP Insight Control on HP ProLiant ML and DL series servers or HP BladeSystem servers https://h20195.www2.hp.com/v2/GetPDF.aspx/4AA0-9972ENW.pdf

3-Year HP 24x7 4 hour Response, Hardware Support Onsite Service
Provides for the deployment and basic configuration of HP Insight Control on HP ProLiant ML and DL series servers or HP BladeSystem servers https://h20195.www2.hp.com/v2/GetPDF.aspx/4AA0-9972ENW.pdf

3-Year , HP 24x7 Software Support for Insight Control
Provides for the deployment and basic configuration of HP Insight Control on HP ProLiant ML and DL series servers or HP BladeSystem servers
https://h20195.www2.hp.com/V2/GetPDF.aspx/5981-6645EEE.pdf

Additional Services: Software OS (Microsoft, Linux (SUSE/Red Hat) & VMware Installation & Start Up and Software Support); +10 Proactive Select Credits, Factory Express

The packages include HP Insight Remote Support that uses proven technology to deliver secure, reliable 24x7 remote monitoring, diagnoses, and problem resolution. It is available at no additional cost to all warranty, HP Care Pack Service, and service agreement customers.

To learn more on HP ProLiant servers and HP BladeSystem servers, please contact your HP sales representative or HP Authorized Channel Partner. Or visit: https://www.hp.com/services/proliant

HP ProLiant DL2x170h G6 E5504 1P 6GB-U Hot Plug 8 LFF 1200W PS Server
503581-xx1

HP ProLiant DL4x170h G6 E5504 1P 6GB-U Hot Plug 8 LFF 1200W PS Server
503578-xx1

516828-B21

516816-B21

461135-B21

507750-B21

530888-B21

DIMM slot and configuration diagrams
Basic memory slot & population diagram

• Population order; start with "A" first, "B" second, "C" third, etc. Channel 1 is channel furthest away from the CPU and Channel 3 is channel closest to CPU.

Standard memory configuration (1 CPU model)

• 6GB, consisting of three (3) 2GB dual-rank PC3-10600E UDIMMs

Standard memory plus optional memory (1 CPU model)

• 12GB, consisting of three (3) 2GB UDIMMs plus three (3) 2GB UDIMMs
  
  • 6x 2GB dual-rank PC3-10600E UDIMMs

Standard memory replaced with optional memory (1 CPU model)
RDIMM maximum configuration

• 96GB, consisting of six (6) 16GB quad-rank PC3-8500 RDIMMs

Standard memory replaced with optional memory (2 CPU model)
RDIMM maximum configuration

• 192GB, consisting of sixteen (16) 16GB quad rank PC3-8500 RDIMMs

UDIMM maximum configuration

• 48GB, consisting of twelve (12) 2GB dual-rank PC3-10600 UDIMMs

Drive Support

DVD-ROM

Up to 2 per node

External

USB

Up to 2 per node

External

USB

Hard Drives
NOTE: The components of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and the server backplane) should operate at the same data transfer rate or the system bandwidth will be negotiated down to an acceptable level for all components.
NOTE: Hard drives have either a one year or three year warranty; refer to the specific hard drive QuickSpecs for details.

To drill down to calculators:
- Click on: "ProLiant Servers"
- Click on the Server of interest. Example: HP ProLiant DL1000 G6
- Click on: "Power Calculator" link. (You may need to scroll down to see it)

One 6' Highline (IEC-IEC) power cord ships standard
NOTE: ProLiant DL servers are primarily connected to PDU's in data center racks so they ship standard with only a PDU power cord (416151-B21). If a user wishes to power a ProLiant DL server using a 110V receptacle (NEMA-15), the NEMA power cord (227099-001) must be ordered separately.

NOTE: Japan BTO and CTO configurations get the 6' 4165151-291 power cord in addition. China BTO and CTO configurations get the 6' 416151-AA1 power cord in addition.

NOTE: If customers require a local power cord, they can check the power cord matrix for the appropriate cord. Please see the following power cord matrix: https://www.hp.com/go/powercordmatrix.

Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling programs in many geographic areas. For trade-in information, please go to: https://www.hp.com/go/green. To recycle your product, please go to: https://www.hp.com/go/green or contact your nearest HP sales office. Products returned to HP will be recycled, recovered or disposed of in a responsible manner.

The EU WEEE directive (2002/95/EC) requires manufacturers to provide treatment information for each product type for use by treatment facilities. This information (product disassembly instructions) is posted on the Hewlett Packard web site at: https://www.hp.com/go/green. These instructions may be used by recyclers and other WEEE treatment facilities as well as HP OEM customers who integrate and re-sell HP equipment.