HP ProLiant 100 G5 Lights-Out
100c Management Card Port (Optional)
5.
SAS Cable (SAS model only)
5.
LAN Port (RJ-45)
6.
Hard Drive Controller Card (Optional)
6.
Rear USB 2.0 Ports
7.
System Board
7.
Serial Port
8.
HP ProLiant 100
G5 Lights-Out 100c Management Card Port (Optional)
8.
VGA Port
9.
PS/2 Keyboard Port
9.
System Fan
10.
PS/2 Mouse Port
10.
365W Power Supply
11.
Power Supply Outlet
12.
Power Supply Unit (PSU) Fan
What's New
The HP ProLiant ML110 G5 is now available with higher performance processors
(quad-core up to 3.0GHz and dual-core up to 3.16GHz) resulting in better
processing power and increased productivity for the growing businesses.
Support for SATA Non-Hot Plug Entry and Midline Hard Drives
At A Glance
Processor:
Intel® Xeon® processor 3300 series
Intel® Xeon® processor 3200 series
Intel® Xeon® processor 3100 series
Intel® Core™ 2 Duo processor 7000 series
Intel® Pentium® processor 2000 series
Intel® Celeron® processor 400 series
Memory: o Four (4)
DIMM slots
Four (4) DIMM slots
1GB Standard/8GB Maximum of PC2-6400 Unbuffered DDR2 ECC 800 MHz
Storage Controller:
SATA Models: Integrated 6 ports SATA controller
with embedded RAID (4 ports available for hard disks) NOTE: Transfer rate: 3 Gb/s
SATA.
SAS Models: HP SC40Ge Host Bus Adapter with RAID 0, 1 support,
FIO NOTE: When using the SC40Ge with SATA hard drives, 1.5G SATA
hard drives are required. NOTE: Transfer rate: 3 Gb/s SATA.
Internal Drive Support:
4 HDD Support:
Internal SAS storage capacity of up to 1.8TB
(4 x 450GB 3.5" SAS drives)
Internal SATA storage capacity of up to 8.0TB (4 x 2TB 3.5"
SATA drives)
Network Controller:
Embedded NC105i PCI Express Gigabit Ethernet Server
Adapter
Expansion Slots:
Slot 1: PCI 32-bit/33MHz at 3.3V
Slot 2: PCI-Express x8 connector with x1 link
Slot 3: PCI-Express x8 connector with x1 link
Slot 4: PCI-Express x8 connector with x8 link
USB 2.0 Ports:
Eight (8) USB 2.0: 2 front, 4 rear, 2 internal
(one for tape, one for standard USB device)
Management:
Standard Lights Out 100 IPMI 2.0 reporting
Optional HP ProLiant 100 G5 Lights Out 100c Remote
Management Card
Standard HP ProLiant ML110 G5 Easy Set-up CD
Form Factor:
Micro ATX tower (4U)
Warranty:
This product is covered by a global limited warranty
and supported by HP Services and a worldwide network of HP Authorized
Channel Partners. Hardware diagnostic support and repair are available
for one year from date of purchase. Support for software and initial
setup is available for 90 days from date of purchase. Enhancements
to warranty services are available through HP Care Pack services or
customized service agreements. Hard drives have either a one year
or three year warranty; refer to the specific hard drive QuickSpecs
for details. NOTE: Server Warranty includes
1 year parts, 1 year labor, 1-year on-site support with next business
day response. Warranty repairs may be accomplished through the use
of Customer Self Repair (CSR) parts. These parts fall into two categories:
1) Mandatory CSR parts are designed for easy replacement. A travel
and labor charge will result when customers decline to replace a Mandatory
CSR part; 2) Optional CSR parts are also designed for easy replacement
but may involve added complexity. Customers may choose to have HP
replace Optional CSR parts at no charge. Additional information regarding
worldwide limited warranty and technical support is available http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
Intel® Xeon® processor
X3370 (3.00 GHz, 95W, 1333MHz FSB, 12MB) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Xeon® processor
X3360 (2.83 GHz, 95W, 1333MHz FSB, 12MB) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Xeon® Processor
X3220 (2.40 GHz, 95W, 1066MHz FSB, 8MB) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Xeon ® Processor
X3210 (2.13 GHz, 95W, 1066MHz FSB, 8MB) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Dual-Core Processors
Intel® Xeon® processor
E3120 (3.16 GHz, 65W, 1333MHz FSB, 6MB) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Core™ 2®
processor E7400 (2.80 GHz, 65W, 1066MHz FSB, 3MB) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Intel® Celeron® processor
440 (2.0 GHz, 35W, 800MHz FSB, 512KB) NOTE: Available through Configure
To Order only. See Factory Integration Models section for more details.
Cache Memory One of the following depending on Model
12 MB Level 2 cache - Xeon X3370,
X3360
8 MB Level 2 cache - Xeon X3220,
X3210
6 MB Level 2 cache - Xeon X3330,
E3120, E3110
3 MB Level 2 cache - Core2 E7400
1 MB Level 2 cache - Pentium
E2160
512KB Level 2 cache - Celeron
440
Chipset
Intel® 3200
Memory Protection
ECC
ML110 G5 Memory
Type
PC2-6400 unbuffered DDR2 ECC
800MHz
Standard
1 GB
Maximum
8 GB
Network Controller
Embedded NC105i PCI Express
Gigabit Ethernet Server Adapter
Expansion Slots #
Technology
Bus Width***
Connector Width
Bus Number*
Device Number**
Form Factor
Notes
1
PCI
32-bit
N/A
0
30
Full height slot
33MHz/3.3V
2
PCIe
X1
X8
0
28
Full height slot
3
PCIe
X1
X8
2
28
Full length, full height slot
4
PCIe
X8
X8
0
1
Full length, full height slot
*Default bus assignment
(in decimal). Inserting cards with PCI bridges may alter the actual bus
assignment number.
** Slots are enumerated differently based on OS. MS OS's enumerate from
lowest to highest Device ID by bus (starting with the lowest bus).
*** Indicates the number of physical electrical lanes running to a PCI-e
connector. NOTE: PCI-X Interface (PCI 32bit/33MHz compatible)
Storage Controller
SATA Models
Integrated 6 ports SATA controller
with embedded RAID (4 ports available for Hard Disks) NOTE: Transfer rate: 3 Gb/s SATA.
Storage
Optical Drive
SATA DVD-ROM Drive
Hard Drives
(SATA Model only)
160GB SATA 7200 rpm Drive
Maximum Internal
Storage
Type
Non-Hot Plug SAS
1.8TB
(4 x 450GB)
Non-Hot Plug SATA
8.0TB
(4 x 2TB)
Interfaces
Parallel
0
Serial
1
Pointing Device (Mouse, PS2)
1
Graphics
1
Keyboard (PS2)
1
USB 2.0 Ports
8 total (4 rear, 2 front panel, 2 internal (one for USB Tape connectivity))
HP ProLiant 100 G5 Lights-Out
100c Remote Management port (Optional)
Graphics
32MB shared supporting 1600
x 1200 x 16M resolution
Form Factor
Micro ATX Tower (4U)
Remote Management
Lights-Out
100c
Lights Out LO100c is
a Remote Management Card (RMC) for ProLiant 100 series servers that do not have
embedded LO100i. The LO100c has all the features of the LO100i Advanced license
and allows customers, or their service providers, to remotely manage ProLiant
servers over a LAN or the Internet from anywhere, anytime regardless whether the
server is located in the same building, across town, or around the globe.
With LO100c, users can acquire complete remote control with Virtual KVM (graphical
hardware-based, remote console). Users can also access the server's serial console,
control system power, update system firmware and software, as well as monitor
system environmental conditions. The LO100c remote management card can be accessed
from a web browser or command line interface. This virtual "at-the-server"
functionality means administrators stay in control of remote HP ProLiant 100 series
servers.
The HP Lights-Out100c consists of a management processor and firmware
that provides cost-effective, entry-level lights-out functionality, basic system
board management functions, and diagnostics.
The HP ProLiant Easy Set-up CDs optimize single-server setup, providing
a simple way to deploy reliable and consistent server configurations.
The HP ProLiant 100 Series Easy Set-up CD ship standard with the ML110
G5.
It offers essential single-server deployment tools for HP ProLiant 100
series servers that simplify HP entry server setup, providing a repeatable
way to deploy reliable and consistent single-server configurations.
The HP ProLiant Easy Set-up CDs assist with the OS installation process
by preparing the system for installing "off-the-shelf" versions
of Windows operating system software and automatically integrating optimized
HP ProLiant server software drivers and utilities. Users enjoy the following
benefits:
An easy-to-use, intuitive graphical interface that prepares your system
for the OS installation process.
Integration of key server software drivers with assisted installation.
Dependency and validity checks to ensure that all supported ProLiant
software can be installed.
NOTE: For
more information on HP's Certified and Supported ProLiant Servers for OS and Virtualization
Software and latest listing of software drivers available for your server, please
visit our Support Matrix at: http://www.hp.com/go/supportos
and our driver download page http://www.hp.com/support/ML110G5
Factory Express
Portfolio for Servers and Storage
HP Factory Express offers configuration, customization, integration and
deployment services for HP servers and/or storage products. Customers
can choose how their factory solutions are built, tested, integrated,
shipped and deployed.
Factory Express offers service packages for simple configuration, racking,
installation, complex configuration and design services as well as individual
factory services, such as image loading, asset tagging and custom packaging
HP products supported through Factory Express include a wide array of
servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades,
HP BladeSystem, HP 9000 servers, as well as, the MSAxxxx, VA7xxx, EVA,
XP, rackable tape libraries and configurable network switches.
For more information
on Factory Express services for your specific server model please contact
your sales representative or go to http://www.hp.com/go/factory-express.
HP Enterprise Configurator
The HP eConfigure Enterprise Configurator now provides factory default
racking for our HP hardware portfolio. This approach is aligned with our
strategic direction to meet the needs and expectations of our valued customers.
If you require "custom" rack configuration, please contact HP's
Customer Business Center or an Authorized Partner for assistance. http://www.hp.com/products/configurator.
Service and Support
HP Care Pack Services provide total care and support expertise with committed
response designed to meet your IT and business needs.
HP Care Pack services include coverage for the HP branded hardware options
qualified for the server that are purchased at the same time or afterward
and internal to the enclosure. It also includes the 22" and smaller
external monitors and tower UPS options up to 3kVA. These items will be
covered at the same service level and for the same coverage period as
the server. Coverage of UPS Battery is not included and standard warranty
terms & conditions apply. For servers or storage systems installed
within a rack, service also covers all HP qualified rack options installed
within the same rack.
To fully capitalize on your HP ProLiant servers' capabilities requires
a service partner who thoroughly understands your server technology and
systems environment. HP Services, an industry leader in provision of multi
vender support solutions provides a range of support services designed
to meet the varying needs of business. Whether an SMB or large global
corporation HP has a ProLiant server support offer to help you speedily
deploy and maximize system uptime.
Recommended Service Simplify ProLiant solution implementation,
maintenance and management.
Support Service 3 Year, 9x5 Next Business Day coverage,
excluding HP holidays only
Deployment Service Hardware Installation only
Enhanced Service Optimize service level to increase IT
performance and availability
Support Service 3 Year 13x5 Same Business Day, 4-Hour
response coverage
Deployment Service Installation and Start-up only
Installation & Start-Up of a ProLiant server and Microsoft or Linux
O/S per the Customer Description and/or Data Sheet. To be delivered on
a scheduled basis 8am-5pm, M-F, excl. HP holidays.
NOTE:
For the Standard Features shipped in the "Factory Integrated Models",
please see "Configuration Information - Factory Integrated Models"
section".
The
ProLiant Smart Buy program offers a collection of promotional server and option
products that are configured with SMB in mind, offered at discounted prices, and
positioned for quick delivery. Smart Buy server offers are available for a limited
time only.
NOTE:
This section lists some of the steps required to configure a Factory Integrated
Model. To ensure only valid configurations are ordered, HP recommends the
use of an HP approved configurator. Contact your local sales representative
for information on CTO product offerings and requirements. NOTE: HP does not allow factory integration of options into standard
models listed above.
Configure-to-order servers must start with a CTO Chassis. NOTE: FIO indicates that this option is a Factory Installable Option.
Step 1:
Base Configuration
Models
HP ProLiant ML110G5 NHP CTO Chassis
445607-B21
Factory Integrated Models ship
with:
Embedded NC105i PCI Express Gigabit
Ethernet Server Adapter
Keyboard and Mouse NOTE: Keyboard and Mouse option needs
to be manually selected for shipment. Please see the USB Options listed
in the options selection of this QuickSpecs.
Power cord
Micro ATX Tower (4U)
NOTE: HP SATA
drive models are limited to 4.0TB support.
NOTE: The components
of a storage subsystem (e.g. the drive, the HBA/controller, and firmware)
should operate at the same data transfer rate or the system bandwidth will
be negotiated down to an acceptable level for all components. NOTE: Hard drives have either a one year or three year warranty;
please refer to the specific hard drive QuickSpecs for details. NOTE: Supports up to 4 hard drives.
SATA Non-Hot Plug LFF (3.5-inch)
Midline (MDL) Drives
HP 2TB 3G SATA 7.2K rpm LFF (3.5-inch)
Non-hot Plug Midline 1yr Warranty Hard Drive
Step 3: Choose Additional
Options for Factory Integration
HP Storage Controller
HP SC40Ge SAS HBA, FIO
449176-B21
Step
4: Choose Additional Options for Factory Integration NOTE: For additional "Core Options"
and "Additional Options", please refer to the "Options"
sections below.
NOTE: The components
of a storage subsystem (e.g. the drive, the HBA/controller, and firmware)
should operate at the same data transfer rate or the system bandwidth will
be negotiated down to an acceptable level for all components. NOTE: Hard drives have either a one year or three year warranty;
please refer to the specific hard drive QuickSpecs for details.
SATA Non-Hot Plug LFF (3.5-inch)
Midline (MDL) Drives
HP 2TB 3G SATA 7.2K rpm LFF (3.5-inch)
Non-hot Plug Midline 1yr Warranty Hard Drive
HP Non-Hot Plug SAS/SATA 4-Port
Cable Kit NOTE: The purchase of a SAS Storage
Controller requires the purchase of HP SAS/SATA 4-Port Cable (P/N 457692-B21).
HP SC44Ge Host Bus Adapter NOTE: When using the SC44Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required. Transfer rate: 1.5
Gb/s SATA, 3 Gb/s SAS. NOTE: Supports RAID 0,1.
NOTE: For the
complete range of StorageWorks tape drives, autoloaders, libraries and media
see: http://www.hp.com/go/tape.
For hardware and software compatibility of HP StorageWorks tape backup products
see: http://www.hp.com/go/connect.
HP StorageWorks DAT 320 USB Internal
Tape Drive
AJ825A
HP StorageWorks DAT 320 SAS Internal Tape Drive NOTE: Connection using the HP SC44Ge
SAS Host Bus Adapter ( 416096-B21) recommended.
AJ830A
HP StorageWorks LTO-2 Ultrium
448 SAS Internal Tape Drive NOTE: Connection using the HP SC44Ge
SAS Host Bus Adapter ( 416096-B21) recommended.
DW085A
HP StorageWorks LTO-3 Ultrium
920 SAS Internal Tape Drive NOTE: Connection using the HP SC44Ge
SAS Host Bus Adapter ( 416096-B21) recommended.
EH847A
HP StorageWorks 1/8 G2 LTO-3 Ultrium
920 SAS Tape Autoloader NOTE: Requires HP 1U Tape Autoloader
Rack-Mount Kit (AH166A) for rack installation. Connection using the HP SC44Ge
SAS Host Bus Adapter ( 416096-B21) recommended.
AH558A
HP StorageWorks MSL2024 Tape Library
with one LTO-3 Ultrium 920 SAS Drive NOTE: Connection using the HP SC44Ge
SAS Host Bus Adapter ( 416096-B21) recommended.
NOTE: For additional
information regarding KVM Switches, Serial Console servers, rack mount monitors,
keyboards and all related options please see the following URL: http://www.hp.com/go/kvm
NOTE: Memory configurations
listed do not apply to "Factory Integrated Models".
Standard Memory
SATA Models:
1 GB of PC2-6400 DDR2 SDRAM running at 800MHz with ECC capabilities memory
installed.
Standard Memory Plus Optional
Memory
Up to 6 GB memory is available
with the optional installation of 2 x 2 GB + 2 x 1 GB PC2-6400 un-buffered
ECC DDR2 SDRAM DIMM Memory kits.
Standard Memory Replaced
with Optional Memory
Up to 8GB of memory is available
with the removal of the standard 1 GB of memory and the optional installation
of 4x 2 GB PC2-6400 un-buffered ECC DDR2 SDRAM DIMM Memory kits.
NOTE: The below
chart does not represent all possible memory configurations. NOTE: For best performance, it is recommended that customer installs
memory in identical pairs (Slots 1 and 3 are interleaving pair. Slots 2
and 4 are interleaving pair).
ML110 G5 Memory
Slot
1
2
3
4
Standard
1 GB
1 GB
Empty
Empty
Empty
Optional
6 GB
1 GB
2 GB
1 GB
2 GB
Maximum
8 GB
2 GB
2 GB
2 GB
2 GB
Following are memory
options available from HP:
HP Memory
HP 2GB (1x2GB) Dual Rank PC2-6400
(DDR2-800) Unbuffered Memory Kit
ML110 G5 Hard Drives (SATA Models
only) NOTE: The components of a storage
subsystem (e.g. the drive, the HBA/controller, and firmware) should operate
at the same data transfer rate or the system bandwidth will be negotiated
down to an acceptable level for all components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
SATA Non-Hot Plug
LFF (3.5-inch) Midline (MDL) Drives
Quantity
Supported
Position
Supported
Controller
2TB 3G 7.2K
1TB 3G 7.2K
500GB 3G 7.2K
Up to 4
3,4,5,6
6 Port SATA controller with Embedded
RAID on Motherboard NOTE: Transfer rate: 3 Gb/s SATA
SATA Non-Hot Plug
LFF (3.5-inch) Entry (ETY) Drives
Quantity
Supported
Position
Supported
Controller
250GB 3G 7.2K
160GB 3G 7.2K
Up to 4
3,4,5,6
6 Port SATA controller with Embedded
RAID on Motherboard NOTE: Transfer rate: 3 Gb/s SATA
ML110 G5 Hard Drives (SAS Models
only)
SAS Non-Hot Plug LFF
(3.5-inch) Enterprise (ENT) Drives
Quantity
Supported
Position
Supported
Controller
450GB 3G 15K DP
300GB 3G 15K DP
146GB 3G 15K DP
Up to 4
3,4,5,6
HP 4 Internal Port SAS HBA SC40Ge
with RAID (0,1) NOTE: When using the SC40Ge with
SATA Hard Drives, 1.5G SATA Hard Drives are required.
Maximum Storage
Capacity SATA/SAS Models
Internal
SATA
8.0TB (4 x 2TB)
SAS
1.8TB (4 x 450GB)
Tape and Disk Backup
NOTE:
For the complete range of StorageWorks tape drives, autoloaders, libraries
and media, including the internal fitting models, see: http://www.hp.com/go/tape.
For the complete range of StorageWorks D2D Backup Systems see: http://www.hp.com/go/d2d.
For the complete range of StorageWorks RDX drives and media see: http://www.hp.com/go/rdx.
For hardware and software compatibility of HP StorageWorks disk and tape
backup products see: http://www.hp.com/go/connect.
Position
Recommended Controller
Part Number
HP StorageWorks SCSI Tape Drives
LTO-1 Ultrium 232
LTO-2 Ultrium 448
LTO-3 Ultrium 920
LTO-3 Ultrium 960
LTO4 Ultrium 1760
LTO-4 Ultrium 1840
DAT 40
DAT 72
DAT 160
HP StorageWorks Fibre Channel
Tape Libraries
MSL2024
MSL4048
MSL8096
MSL6000
External
Please consult the
EBS connectivity matrix at: http://www.hp.com/go/ebs
for connectivity information and the supported Fibre Channel HBAs shown
in this QuickSpecs.
HP StorageWorks USB RDX Removable Disk Backup System
RDX160
RDX320
RDX500
RDX750
System Leakage with all power supplies loaded
(mA)
0.45mA@120V
System Inrush Current with all power supplies
loaded (A)
<150A@ 240Vac
Power cord requirements
Nema 5-15P to IEC320-C13
IEC320-C13 to IEC320-C14
**Power shown is for
a fully configured system consisting of (1) CPU, (4) double-sided DIMMs,
(4) HDDs, (1) DVD-ROM, (4) PCI cards, and (1) power supply.
Maximum
(all hard drives, power supplies, and processors installed)
39 lb (17.5 kg)
Minimum
(one hard drive, power supply, and processor installed)
23.81 lb (10.8 kg)
Input Requirements
(per power supply)
Rated Line Voltage
90 to 132 VAC,
180 to 264 VAC
Rated Input Current
6 A (at 100 VAC),
3 A (at 200 VAC)
Rated Input Frequency
47 to 63 Hz
Rated Input Power
600 W (at 100 VAC),
600 W (at 200 VAC)
Power Supply Output
(per power supply)
Rated Steady-State Power
365 W (at 100 VAC),
365 W (at 200 VAC)
Maximum Peak Power
385 W (at 100 VAC),
385 W (at 200 VAC)
System Inlet Temperature
Operating
10° to 35°C (50° to
95°F) at sea level with an altitude derating of 1.0°C per every
305 m (1.8°F per every 1000 ft) above sea level to a maximum of 3050
m (10,000 ft), no direct sustained sunlight. Maximum rate of change is 10°C/hr
(18°F/hr). The upper limit may be limited by the type and number of
options installed.
System performance may be reduced if operating with a fan fault or above
30°C (86°F).
Non-operating
-30° to 60°C (-22°
to 140°F). Maximum rate of change is 20°C/hr (36°F/hr).
Relative Humidity
(non-condensing)
Operating
10% to 90% relative humidity (Rh),
28°C (82.4°F) maximum wet bulb temperature, non-condensing.
Non-operating
5% to 95% relative humidity (Rh),
38.7°C (101.7°F) maximum wet bulb temperature, non-condensing.
Altitude
Operating
3050 m (10,000 ft). This value
may be limited by the type and number of options installed. Maximum allowable
altitude change rate is 457 m/min (1500 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable
altitude change rate is 457 m/min (1500 ft/min).
Acoustic Noise
Listed are the declared
A-Weighted sound power levels (LWAd) and declared average bystander position
A-Weighted sound pressure levels (LpAm) when the product is operating in
a 23°C ambient environment. Noise emissions were measured in accordance
with ISO 7779 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
SATA Model
Idle
L WAd
4.2 Bels
L pAm
26 dBA
Operating
L WAd
5.1 Bels
L pAm
34 dBA
SAS Model
Idle
L WAd
5.2 Bels
L pAm
34 dBA
Operating
L WAd
5.7 Bels
L pAm
40 dBA
Emissions Classification
(EMC)
FCC Rating
Class B
Normative Standards
CISPR 22; EN55022; EN55024; FCC
CFR 47, Pt 15; ICES-003; CNS13438; GB9254; K22;K24; EN 61000-3-2; EN 61000-3-3;
EN 60950-1; IEC 60950-1
NOTE:
Product conformance to cited product specifications is based on sample (type)
testing, evaluation, or assessment. This product or family of products is
eligible to bear the appropriate compliance logos and statements.
HP 160GB 3G SATA
7.2K rpm LFF (3.5-inch) Non-hot Plug Entry 1yr Warranty Hard Drive
CD-ROM, CD-XA, CD-DA
(Mode 1, Mode 2, Form 1 and 2)
Photo CD (Single and Multi-session)
CD-R, CD-RW
Mixed Mode (Audio and Data combined)
DVD-ROM
DVD-R/RW, DVD+R/RW
CD-R, CD-RW, DVD-ROM, DVD+R, DVD+RW
Capacity
4.7 GB (DVD-5)
8.54 GB (DVD-9)
Block Size
DVD Media
2,048 bytes
Interface
SATA
Access Times (typical)
Random
<140 ms
Full-Stroke
<250 ms
Data Transfer Rate
Sustained
8100 to 21600 KB/s (6X to 16X)
Bus Rate
1.5 Gbps
Cache Buffer
128 KB
Start-up Time (typical)
< 7 seconds
Stop Time
< 4 seconds
Laser Parameters
Type
Semiconductor Laser GaA1As
Wave Length
780 ± 25 nm
Operating Conditions
Temperature
41° to 122° F (5° to 50° C)
Humidity
10% to 90%
Dimensions
(HxWxD, maximum)
1.7 x 5.85 x 8.11 in (42.9 x 150
x 195 mm)
Weight
2.64 lb (1.2 kg)
HP 4 Internal Port SAS Host Bus Adapter (SAS/SATA HP Model)
SATA
Protocol
SATA 1.5Gb/s
SATA Ports
4
internal
Port transfer
rate
1.5 Gb/s total
Maximum Capacity
up to 4.0TB (4 x 1TB Non-Hot Plug
SATA HDD)
RAID
Levels Supported
RAID 1 (Mirroring)
RAID 0 (Striping)
Logical
RAID Volumes Supported
2
Dimensions (excluding bracket)
6.6
x 2.5 x 0.6 in (16.8 x 6.4 x 1.6 cm)
Disk
Drive and Enclosure Protocol Support
3
Gbps SAS (Serial Attached SCSI) 1.5 Gbps SATA (Serial Advanced Technology
Attachment)
Architecture
64-bit
SAS Connectors
1
internal SFF8484 x4 Wide SAS Connectors 12 Gbps per x4 Wide SAS Port (4 x
3 Gbps)
Data Transfer
Method
PCI-Express x8 - 2 GB/s
maximum bandwidth
PCI
Bus Speed
PCI-Express x8
Simultaneous Drive Transfer
Ports
1 x4 Wide SAS Connectors
Port Transfer Rate
12
Gb/s per x4 Wide SAS Port (4 x 3 Gb/s)
Software
upgradeable Firmware
Yes
Maximum Capacity
1.2TB
(4 x 300GB)
Memory
Addressing
64-bit, supporting
servers memory greater than 4 GB
Logical
Drives Supported
Up to 2 Logical
Volumes Up to 10 drives total in all RAID volumes Up to 2 Drives per RAID
1 Up to 4 Drives per RAID 0
RAID
Support
RAID 1 (Mirroring)
RAID 0 (Striping)
Upgradeable
Firmware
4-MB flashable ROM
Disk Drive and Enclosure Protocol
Support
3 Gbps SAS and 1.5 Gbps
SATA
HP SC40Ge SAS Host Bus Adapter with RAID
RAID Support
RAID 1 (Mirroring)
RAID 0 (Striping)
Logical Drives Supported
Up to 2 Logical Volumes
Up to 10 drives total in all RAID
volumes
Up to 2 Drives per RAID 1
Up to 8 Drives per RAID 0
Maximum Capacity
3.6TB (8 x 450GB)
Data Transfer Method
PCI-Express x8 - 2 GB/s maximum
bandwidth
Port Transfer Rate
12 Gb/s per x4 Wide SAS Port (4
x 3 Gb/s)
Simultaneous Drive Transfer Ports
2 x4 Wide SAS Connectors
Protocols
3 Gbps SAS and 1.5 Gbps SATA
1.5 Gbps SATA (Serial Advanced Technology
Attachment)
External SAS Connectors
None
Internal SAS Connectors
2 internal SFF8484 x4 SAS Connectors
Upgradeable Firmware
4MB flashable ROM
Embedded NC105i PCIe Gigabit Server Adapter
Network Interface
Integrated 10/100/1000BASE-T
Transceiver
Combines a triple-speed
IEEE 802.3TM Compliant Media Access Controller (MAC) with a triple-speed
Ethernet transceiver.
Data Transfer Method
Compliant to x1 PCIe
Specification
Controller
BCM5722
Network Transfer
Rate
10Base-T (Half-Duplex)
10 Mb/s
10Base-T (Full-Duplex)
20 Mb/s
100Base-TX (Half-Duplex)
100 Mb/s
100Base-TX (Full-Duplex)
200 Mb/s
1000Base-TX (Half and Full-Duplex)
2000Mb/s
Connector
RJ-45 connector
Cable Support
Performs all the physical
layer functions for 10BASE-T, 100BASE-T, and 1000BASE-T Ethemet on standard
Category 5 UTP
Environment-friendly Products and Approach
End-of-life Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go
to http://www.hp.com/go/green.
To recycle your product, please go to: http://www.hp.com/go/green
or contact your nearest HP sales office. Products returned to HP will
be recycled, recovered or disposed of in a responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide
treatment information for each product type for use by treatment facilities.
This information (product disassembly instructions) is posted on the Hewlett
Packard web site at: http://www.hp.com/go/green.
These instructions may be used by recyclers and other WEEE treatment facilities
as well as HP OEM customers who integrate and re-sell HP equipment.