Two U320
hot plug drive bays (SATA models also available)
5.
Sliding rails standard
for in rack servicing
6.
Optional redundant
power supplies
7.
1
full length and 1 half length PCI-X slots (optional PCI Express)
At
A Glance
Combining concentrated 1U compute power,
integrated Lights-Out management, and essential fault tolerance, the HP ProLiant
DL360 is optimized for space constrained data center installations
Up
to 2 Intel Xeon 3.0 GHz/1MB, 3.4 GHz/1MB and 3.6 GHz/1MB Processors with 800MHz
front side bus
Intel E7520 chipset
64-bit Intel® Xeon™ processors with 32-bit & 64-bit
computing
Up to 8 GB of PC2700
DDR 333 SDRAM; system can be configured for 2:1 interleaving
Two
64 bit/133 MHz PCI-X slots (one full length slot and one half length); optional
PCI-Express
Fan redundancy,
standard
460-Watt hot plug
power supply with optional 1+1 redundancy
HP
Power Regulator for ProLiant delivering server level, policy based power management
with industry leading energy efficiency and savings on system power and cooling
costs
Integrated Lights-Out featuring new firmware
v 1.70 with support for Power Regulator for ProLiant and introducing support for
the draft DMTF System Management Architecture for Server Hardware Command Line
Protocol standard
Integrated
Lights-Out (iLO) remote management embedded on every HP ProLiant DL360
Support for new iLO Shared Network
Port enables access to the iLO management processor through one of the embedded
system NICs
Supports
up to two Ultra320 hot plug hard drives; Serial ATA models also available
Three USB ports available: rear, front,
internal
1U Rack form factor
(1.75")
New spring-loaded Universal
sliding rails for in rack servicing ship standard; optional ambidextrous cable
management arm
ProLiant Essential
Foundation Pack standard, including HP Systems Insight Manager, SmartStart, SmartStart
Scripting Toolkit, Subscriber's Choice and ROM Based Setup Utility (RBSU)
Protected by HP Services and a worldwide network of resellers
and service providers. Three-year Next Business Day, on-site limited global warranty.
Certain restrictions and exclusions apply. Pre-Failure Notification on processors,
memory, and SCSI hard drives. SATA hard drives have a one-year warranty.
NOTE: Please
see the SATA Hard Drive QuickSpecs for Technical Specifications such as capacity,
height, width, interface, transfer rate, seek time, physical configuration, and
operating temperature: Serial ATA Hard Drive QS: http://h18000.www1.hp.com/products/quickspecs/11940_na/11940_na.html
NOTE:
For the Standard Features shipped in the "Factory Integrated Models",
please see the "Configuration Information - Factory Integrated Models"
section.
Processor One of the following depending on Model
Intel Xeon Processor 3.0 GHz/800MHz
-1MB L2
Intel Xeon Processor 3.4 GHz/800MHz
-1MB L2
Intel Xeon Processor 3.6 GHz/800MHz
-1MB L2
Cache
Memory
1MB Level 2 cache
Upgradeability
Upgradeable
to dual processing
Chipset
Intel chipset is E7520
Memory
Type
PC2700 DDR 333 SDRAM
Standard
1 GB (1 x 1024 MB)
Maximum
8 GB
Memory Protection
Online spare
Advanced ECC
Network Controller
Embedded NC7782 Dual Port NIC
Expansion
Slots
Slot Number
Bus
Speed
Bus Number*
Device
Number**
Hot Plug
PCI
Voltage
Notes
1
64bit/133MHz
PCI-X
7
0
no
3.3 Volt
1
PCI
Express x8(optional)
3
0
no
n/a
2
64bit/133MHz
PCI-X
10
0
no
3.3 Volt
2
PCI
Express x8(optional)
13
0
no
n/a
*NOTE:
Default bus assignment. Inserting cards with PCI bridges may alter the actual
bus assignment number. **NOTE: Slots are enumerated differently based
on OS. MS OS's enumerate from lowest to highest Device ID by bus (starting with
the lowest bus). NOTE: For more information regarding PCI-X, please
see the following URL: http://www.hp.com/servers/pci-x. NOTE: All slots can accept universal keyed PCI cards.
Manageability
Integrated Lights-Out (iLO) Management (integrated on motherboard)
Storage Controllers
SCSI Models
Smart Array 6i Controller (integrated
on system board of SCSI models) NOTE: The HP ProLiant DL360 G4 does
not offer an external SCSI port.
SATA Models
HP embedded 2 Port SATA Controller
(integrated on system board of SATA models) NOTE: The HP ProLiant DL360 G4 does
not offer an external SCSI port.
Storage
Diskette Drive
1.44 MB Diskette Drive; optional
in some models
Optical Drive
24x IDE CD-ROM Drive (Low-Profile)
(ejectable); optional in some models
Integrated ATI RAGE XL Video
Controller with 8-MB SDRAM Video Memory
Form Factor
Rack (1U), (1.75 in/4.45 cm)
ProLiant
Essentials Foundation Pack Software
HP Systems Insight Manager
HP's
new HP Systems Insight Manager (HP SIM) helps maximize system uptime and performance
and reduce system maintenance costs by providing proactive notification of problems
before those problems result in unplanned downtime or reduced productivity. HP
SIM are both easy to set up work with the Insight Management Agents, integrated
Light-Out and Remote Insight Lights-Out Edition, and Version Control Agents to
deliver robust fault, configuration, and asset management as well as remote administration.
With HP SIM customers will also be able to take advantage of role-based security;
the ability to manage ProLiant, Integrity, and HP 9000 systems; and plug-ins for
storage, client, printer, and power management as well as server rapid deployment,
performance management, and workload management. For more details on HP SIM visit
http://www.hp.com/go/hpsim.
SmartStart
SmartStart
is a tool that simplifies server setup, providing a rapid way to deploy reliable
and consistent server configurations. For more information, please visit the SmartStart
Web site at http://www.hp.com/servers/smartstart.
SmartStart version supported (minimum): SmartStart 7.10.
Management
Agents
The Management Agents
form the foundation for HP's Intelligent Manageability strategy. They provide
direct, browser-based access to in-depth instrumentation built into HP servers,
workstations, desktops, and portables, and send alerts to HP System Insight Manager
and other enterprise management applications in case of subsystem or environmental
failures. For additional information about the Management Agents and other management
products from HP, please visit the management Web site at http://www.hp.com/servers/manage.
Subscriber's Choice
Subscriber's
Choice Driver and Support Alerts/Notifications is a web-based email subscription
service that provides automatic delivery of software and driver change notifications
for ProLiant products. Sign up at http://www.hp.com/go/subscriberschoice
and customize your profile to receive various new alerts as they become available,
on a weekly or monthly basis.
ROMPaq,
support software, and configuration utilities
The
latest software, drivers, and firmware fully optimized and tested for your ProLiant
server and options available in SmartStart or downloadable from Software and Drivers
download pages: http://www.hp.com/go/support
Insight Diagnostics Online
Edition
The most advanced configuration
analysis, reporting and troubleshooting utilities used by HP and at your fingertips,
available in SmartStart.
Optional
ProLiant Essentials Value Packs
Optional software offerings that selectively extend the functionality of an
Adaptive Infrastructure to address specific business problems and needs:
Rapid Deployment Pack - an automated solution for multi-server deployment
and provisioning, enabling companies to quickly and easily adapt to changing business
demands.
Workload Management Pack - provides easier management of complex
environments, improving overall server utilization and enabling Windows® 2000
customers for the first time to confidently deploy multiple applications on a
single multiprocessor ProLiant Server.
Integrated Lights-Out Advanced
Pack - upgrades the Integrated Lights-Out processor to full virtual presence and
control with graphical console and virtual media.
Performance Management
Pack - a performance management solution that identifies and explains hardware
performance bottlenecks on ProLiant servers and attached options enabling users
to better utilize their valuable resources.
Intelligent Networking
Pack - detects and analyzes network bottlenecks or broken network linkages and
steers traffic to the optimum route based on network conditions, plus it provides
an extra layer of protection. The virus throttle feature of the solution slows
the propagation of fast spreading virus
Vulnerability and Patch
Management Pack - identifies and remediates software security vulnerabilities
due to missing patches as well operating system configurations that can be exploited
by viruses, worms, and other blended threats
Virtual Machine Management
Pack - provides central management and control of virtual machines from Microsoft
and VMware. Integrated approach provides the ability to manage both physical and
virtual resources from a single management console.
Server Migration
Pack - The Server Migration Pack automates the manual processes required for migrating
servers between physical or virtual platforms (P2V, V2P, and V2V).
NOTE: Flexible
and volume quantity license kits are available for ProLiant Essentials Value Packs.
Refer to http://www.hp.com/servers/proliantessentials
or the various ProLiant Essentials Value Pack product QuickSpecs for more information.
NOTE: For more information regarding ProLiant Essentials Software,
please see the following URL: http://www.hp.com/servers/proliantessential.
Industry Standard
Compliance
ACPI 1.0b Compliant
PCI 2.2 Compliant
Microsoft® Logo certifications
USB 1.1 and 2.0 Compliant
Remote Manageability
Integrated Lights-Out (iLO) Standard Management:
Virtual Text Remote Console
Virtual Power Button Control
Dedicated & shared LAN Connectivity
Browser and command line access
Automatic IP Configuration via DHCP/DNS/WINS
Industry Standard 128-bit Secure Sockets Layer (SSL) and Secure Shell
Security
IML and iLO Event Logging
Support for 12 user accounts with customizable access privilege
Integrated Lights Out Advanced Pack (optional)
Remote Lights out Edition ll (optional)
Intelligent Manageability
HP Systems Insight Manager
SmartStart
Remote Insight Lights-Out Edition ll (optional)
ROM-Based Setup Utility (RBSU)
Remote-Flash Redundant ROM
Integrated Management Log (IML)
Server Health logging
Automatic Server Recovery-2 (ASR-2)
System Interconnect Status Indicators
Dynamic sector repairing and drive parameter tracking (with Smart Array
controllers)
Hot Spare Boot
(NOTE: Upon the event of a failed
processor or VRM in a multi-processing environment, the system will automatically
reboot and use the remaining good processor(s).)
Power Down Utility
Pre-Failure Warranty (covers processors, as well as SCSI hard drives and
memory)
Security
Power-on password
Keyboard password
Diskette drive control
Diskette boot control
QuickLock, Network Server Mode
Removable CD and Floppy Drive Assembly
Serial interface control
Administrator's password
Disk configuration lock
Integrated Lights-Out has 12 customizable user accounts and SSL encryption
Integrated Lights-Out can be disabled via a Global Setting
Server Power Cords
High line cord ships standard
with all part numbers, an additional low line cord
460W Optional (1+ 1 redundant)
power supply NOTE: PN 354587-B21 contains the
optional power supply and an IEC power cable only; purchase if connecting
to PDU/UPS that supports IEC cables. PN 354587-001 contains a low line (NEMA)
power cord only.
Rack 10000 series Cabinets
The increasing power of new high-performance processor technology requires
increased cooling efficiency for rack-mounted servers. The 10000 Series
Racks provide enhanced airflow for maximum cooling, allowing these racks
to be fully loaded with servers using the latest processors.
CAUTION: If a third-party rack
is used, observe the following additional requirements to ensure adequate
airflow and to prevent damage to the equipment:
Front and rear doors:
If your 42U server rack includes closing front and rear doors, you must
allow 830 square inches (5,350 sq cm) of hole evenly distributed from
top to bottom to permit adequate airflow (equivalent to the required
64 percent open area for ventilation).
Side: The clearance between the installed
rack component and the side panels of the rack must be a minimum of
2.75 inches (7 cm).
CAUTION: Always use blanking panels
to fill all remaining empty front panel U-spaces in the rack. This arrangement
ensures proper airflow. Using a rack without blanking panels results in
improper cooling that can lead to thermal damage.
NOTE: For additional information, refer to the Setup and Installation Guide
or the Documentation CD provided with the server, or to the server documentation
located in the Support section at the following URL: http://h18000.www1.hp.com/products/servers/proliantdl360/index.html.
Factory Express Portfolio for
Servers and Storage
HP Factory Express offers configuration, customization, integration and
deployment services for HP servers and storage products. Customers can
choose how their factory solutions are built, tested, integrated, shipped
and deployed.
Factory Express offers service packages for simple configuration, racking,
installation, complex configuration and design services as well as individual
factory services, such as image loading, asset tagging, and custom packaging.
HP products supported through Factory Express include a wide array of
servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades,
HP BladeSystem, HP 9000 servers as well as the MSA1000, VA7xxx, EVA, XP,
rackable tape libraries and configurable network switches.
For more information on Factory Express services for your specific server
model please contact your sales representative or go to http://www.hp.com/go/factory-express.
Three-year limited warranty, including hardware diagnostic support, pre-failure
warranty (coverage of hard drives, memory and processors). The warranty
is fully supported by HP Services and a worldwide network of resellers
and service providers. In addition 90-day's getting started software telephone
support may be covered under the warranty or available for an additional
fee. Enhancements to warranty services are available through HP Care Pack
services.
NOTE: Limited warranty includes
3 year parts, 3 year labor, 3-year on-site support. NOTE: SATA drives have a 1 year
warranty.
Care Pack services provide a range of life cycle support options that
let you choose the service levels that meet your business requirements,
from basic to mission-critical.
A full range of HP Care Pack hardware and software services are available
including:
Installation and start up
Education courses
Extended onsite hardware coverage hours from same business day 13
hours, 5 day to 24 hours, 7 days call window with options including
4-hour response or 6-hour Call To Repair
Comprehensive range of software technical support for Microsoft, Linux,
ProLiant Essentials and VMWare-based IT solutions helping to deliver
high level of application availability. Response times range from 30
mins for critical problems to 2 hours.
System Management, Performance Services and Mission Critical Support
Solution
HP Care Pack services include coverage for the HP branded hardware options
qualified for the server, purchased at the same time or afterward, internal
to the enclosure, as well as 22" and smaller external monitors and
tower UPS options up to 3kVA; these items will be covered at the same
service level and for the same coverage period as the server. Coverage
of UPS Battery is not included, standard warranty terms & conditions
apply. For servers or storage systems installed within a rack, service
also covers all HP qualified rack options installed within the same rack.
(1)
Intel Xeon Processor 3.4 GHz/800MHz standard (up to 2 supported)
Cache Memory
1MB
level 2 cache
Memory
2
x 1 GB (Standard) to 8 GB (Maximum) of PC2700 DDR 333 SDRAM
Network
Controller
Embedded NC7782 Dual
Port NIC
Storage
Controller
U320 Smart Array
6i Controller (embedded on system board) NOTE:
The HP ProLiant DL360 Generation 4 (G4) does not offer an external SCSI port.
Hard Drives
None
ship standard; system supports up to two hot plug U320 drives NOTE:
The HP ProLiant DL360 G4 SCSI models only support U320 Universal Hot Plug
drives.
Remote
Management
Integrated Lights-Out
(iLO) Standard Management (embedded)
Power
Supply
Two 460W power supply
(1+ 1 redundant)
Optical
Drive
24x IDE CD-ROM Drive (Low-profile)
Diskette Drive
1.44
MB Diskette Drive
PCI-X
Slots
1 full length and 1 half
length 64bit/133MHz PCI-X slot
Form
Factor
Rack (1U), (1.75 in/4.45
cm)
DL360R04 X3.4-1MB/800, 1GB SCSI 354571-001
Processor
(1) Intel Xeon Processor 3.4 GHz/800MHz standard (up to 2 supported)
Cache Memory
1MB
level 2 cache
Memory
1
x 1 GB (Standard) to 8 GB (Maximum) of PC2700 DDR 333 SDRAM
Network
Controller
Embedded NC7782 Dual
Port NIC
Storage
Controller
U320 Smart Array
6i Controller (embedded on system board) NOTE:
The HP ProLiant DL360 Generation 4 (G4) does not offer an external SCSI port.
Hard Drives
None
ship standard; system supports up to two hot plug U320 drives NOTE:
The HP ProLiant DL360 G4 SCSI models only support U320 Universal Hot Plug
drives.
Remote
Management
Integrated Lights-Out
(iLO) Standard Management (embedded)
Power
Supply
One 460W power supply
(redundant power supply optional)
Optical
Drive
24x IDE CD-ROM Drive (Low-profile)
Diskette Drive
1.44
MB Diskette Drive
PCI-X
Slots
1 full length and 1 half
length 64bit/133MHz PCI-X slot
Form
Factor
Rack (1U), (1.75 in/4.45
cm)
DL360R04 X3.4-1MB/800, 1GB 2P SATA
354570-001
Processor
(2) Intel Xeon Processor 3.4
GHz/800MHz standard
Cache Memory
1MB level 2 cache
Memory
1 x 1 GB (Standard) to 8 GB
(Maximum) of PC2700 333 DDR SDRAM
Network Controller
Embedded NC7782 Dual Port NIC
Storage Controller
Embedded SATA controller; Non-RAID
for controller
Hard Drives
None ship standard; system supports
up to two Serial ATA drives NOTE: When SATA drives are installed,
hot-plug capability and LEDs are not currently supported.
Remote Management
Integrated Lights-Out (iLO)
Standard Management (embedded)
Power Supply
One 460W power supply (redundant
power supply optional)
Optical Drive
Optional on SATA Models
Diskette Drive
Optional on SATA Models
PCI-X Slots
1 full length and 1 half length
64bit/133 MHz PCI-X slot
Configuration Information - Factory Integrated Models
NOTE:
HP does not allow factory integration of options into standard models
listed below.
Configure-to-order servers must start with a CTO Chassis. NOTE:
This product offering does not support HP Factory Express Server Configuration
Level 1.
Step
1: Base Configuration (choose one of the following configurable models)
Models
HP ProLiant DL360G4
SATA Rack CTO Chassis
367006-405
Factory Integrated Model ships with:
NC7782 Dual Port PCI-X Gigabit Server Adapter (embedded)
Non-RAID SATA (SATA RAID functionality is available via OS software RAID)
1 full length and 1 half length 64bit/133 MHz PCI-X slot
Integrated Lights-Out (iLO) embedded
7 fans; Fan redundancy
Rack (1U), (1.75 in/4.45 cm)
HP ProLiant DL360G4
SCSI Rack CTO Chassis
367007-405
Factory Integrated Model ships with:
NC7782 Dual Port PCI-X Gigabit Server Adapter (embedded)
U320 Smart Array 6i Controller (embedded on system board)
1 full length and 1 half length 64bit/133 MHz PCI-X slot
Integrated Lights-Out (iLO) embedded
1.44MB Diskette Drive
7 fans; Fan redundancy
Rack (1U), (1.75 in/4.45 cm)
Step
2: Choose Required Options (only one of the following from each list unless
otherwise noted)
Processors
Intel X3.0GHz/800-1MB
DL360G4 FIO BASE
368152-B21
Intel X3.4GHz/800-1MB
DL360G4 FIO BASE
354582-B21
Intel X3.6GHz/800-1MB
DL360G4 FIO BASE
354583-B21
Base
Memory
512 MB of Advanced
ECC PC2700 DDR SDRAM DIMM Memory Kit (1 x 512 MB)
NOTE:
An Optical Drive is REQUIRED if choosing the 367007-405 SCSI Rack CTO Chassis
Model in Step 1. NOTE: Optical Drives are OPTIONAL if choosing the 367006-405 SATA
Rack CTO Chassis Model in Step 1.
Slimline CD-ROM
Drive 24X NOTE: This CD/ROM Drive (PN 356963-B21)
is for SATA models.
1.44 MB Diskette
drive NOTE: This Diskette Drive is for
SATA (367006-405) models
354588-B21
Optical
Drive
NOTE:
The Optical Drive is OPTIONAL for the SATA Rack CTO Chassis Model (367006-405)
but REQUIRED if choosing the SCSI Rack CTO Chassis Model (367007-405) in
Step 1.
Slimline CD-ROM
Drive 24X NOTE: This CD/ROM Drive (PN 356963-B21)
is for SATA models.
460W HP redundant
power supply with NEMA cord only NOTE: The HP ProLiant DL360 G4 ships
with an IEC-IEC power cord used for rack mounting with Power Distribution
Units (PDUs). For stand-alone deployments or installation without a rack.
Models ship with two power cords: IEC-IEC and NEMA cords.
ProLiant
Essentials Integrated Lights-Out Advanced Pack, 1 server Featuring:
sophisticated virtual administration features for ultimate control of servers
in the data centers and remote sites.
ProLiant
Essentials Intelligent Networking Pack - Windows Edition, Single Server License
NOTE: For use with a single server.
Contains one license with a unique license activation key and documentation.
ProLiant
Essentials Performance Management Pack, Single-Server License NOTE:
For use with a single server. Contains one license with a unique license activation
key, HP Management CD and documentation. NOTE: The most recent version
of the software can always be downloaded at http://www.hp.com/products/pmp.
ProLiant Essentials
Virtual Machine Management Pack, Single-Server License NOTE:
For use with a single server. Contains one license with a unique license activation
key and documentation.
372214-B21
ProLiant
Essentials Server Migration Pack, Single-Migration License NOTE:
Contains one license, enabling 1 server migration, with a unique license activation
key and documentation. NOTE: This license allows 1 server to be migrated
from a physical server to a virtual machine. Or this license can be used to migrate
a virtual machine from one virtualization layer i.e. VMware GSX to a different
virtualization layer such as VMware ESX or Microsoft Virtual Server 2005.
ProLiant
Essentials Vulnerability and Patch Management Pack
ProLiant Essentials
Vulnerability and Patch Management Pack, Single-Server License NOTE:
For use with a single server. Contains one license with a unique license activation
key and documentation.
NOTE:
Flexible and volume quantity license kits are available for ProLiant Essentials
Value Packs. Refer to http://www.hp.com/servers/proliantessentials
or the various ProLiant Essentials Value Pack product QuickSpecs for more information. NOTE: For more information regarding ProLiant Essentials Software, please
see the following URL: http://www.hp.com/servers/proliantessentials.
1.44 MB Diskette Drive NOTE: This 1.44MB Diskette Drive
(PN 354588-B21) is for SATA models.
354588-B21
Hard Drives
Serial-ATA
(SATA) Hard Drives
Serial-ATA
(SATA) Hard Drive (SATA Models only) NOTE: When SATA
drives are installed, hot-plug capability and LEDs are currently not supported. NOTE: SATA drives have a 1 year warranty.
NOTE: Please
see the SATA Hard Drive QuickSpecs for Technical Specifications such as capacity,
height, width, interface, transfer rate, seek time, physical configuration, and
operating temperature: Serial ATA Hard Drive QS: http://h18000.www1.hp.com/products/quickspecs/11940_na/11940_na.html
NOTE: Please
see the following Controller QuickSpecs for Technical Specifications such as PCI
Bus, PCI Peak Data Transfer Rate, SCSI Protocols supported, SCSI Peak Data Transfer
Rate, Channels, SCSI Ports, Drives supported, Cache, RAID support, and additional
information: http://h18000.www1.hp.com/products/quickspecs/12247_na/12247_na.html
(Smart P600 Controller)
NOTE:
A minimum of 1 GB of memory is required for NC370x adapters, with a maximum
of two NC370x adapters permitted in a server. NOTE: Any NIC (except the NC1020) on the option list can be used
for redundancy with the embedded NC7782 Dual Port Network Controller. When
teaming with other NICs or with the embedded NIC, the lack of Jumbo Frames
and LSO features on the NC1020 will cause high end NICs to have those features
disabled. (e.g. incompatibility issues with the other option NICs for that
platform).
HP StorageWorks Ultrium 232 Internal
Tape Drive (Carbonite) NOTE: No internal
tape drives fit inside the HP ProLiant DL360 G4p. The internal drive shown here
is for the 1U or 3U Rack-mount Kit.
HP StorageWorks 1U Rack-Mount
Kit NOTE: The 1U Rack-mount Kit can
support up to (2) half-height tape drives and compatible with multiple Single-Ended
and LVD SCSI tape drives including the DAT 24, DAT 40, DAT 72, DLT VS80, DLT VS160,
Ultrium 215, Ultrium 232 and Ultrium 448 tape drives.
HP
StorageWorks 3U Rack-Mount Kit NOTE: The 3U Rack-mount Kit can
support up to (2) full-height or (4) half-height tape drives and compatible with
multiple Single-Ended and LVD SCSI tape drives including DAT 24, DAT 40, DAT 72,
DLT VS80, DLT VS160, SDLT 320, SDLT 600, Ultrium 215, Ultrium 230, Ultrium 232,
Ultrium 460, Ultrium 448 and Ultrium 960 tape drives.
NOTE: Please
reference the 1/8 Tape Autoloader QuickSpecs at http://www.hp.com/go/automation
for additional information needed to create a complete solution; reference current
compatibility information at http://www.hp.com/go/ebs.
Tape Libraries
HP StorageWorks MSL2024 Tape Library
HP StorageWorks MSL2024 1 Ultrium
960 Drive Library
NOTE: Please reference
the MSL2024 and MSL6000 Tape Library QuickSpecs at http://www.hp.com/go/automation
for additional information needed to create a complete solution; reference
current compatibility information at http://www.hp.com/go/ebs.
NOTE: The HP ProLiant
DL360 G4 ships with an IEC-IEC power cord used for rack mounting with Power
Distribution Units (PDUs). For stand-alone deployments or installation without
a rack, power cord options are available. Model will ship with two power
cords: IEC-IEC (142257-002) and C13-Nema 5-15P (103541-001) cords.
HP
StorageWorks Modular Smart Array 20
HP
StorageWorks Modular Smart Array 20 NOTE:
Rack-mountable 12 (SATA) drive enclosure with U320 Host connectivity, redundant
power supplies.
NOTE: Please see
the StorageWorks Modular SAN Array 1500 cs QuickSpecs for additional options
and configuration information at: http://www.hp.com/go/MSA1500cs
StorageWorks
Options
StorageWorks
2 Gb, 64-bit/133 MHz PCI-X-to-Fibre Channel Host Bus Adapter for Windows 2000,
Windows Server 2003 and Linux NOTE: FCA2214 2 Gb Fibre Channel
Host Bus Adapter is a single channel, 64-bit/133 MHz PCI-X-to Fibre Channel Host
Bus Adapter (HBA) with an embedded multi-mode optical interface
FCA2404DC
- HP StorageWorks 2 Gb, Dual Channel, 133 MHz PCI-X-to-Fibre Channel Host Bus
Adapter for Windows® 2000, and Windows Server 2003 NOTE:
FCA2404DC HP StorageWorks 2 Gb Fibre Channel Host Bus Adapter is a dual channel,
133 MHz, PCI-X to Fibre Channel Host Bus Adapter (HBA) with an embedded multi-mode
optical interface.
323264-B21
FCA2404 - StorageWorks 2 Gb,
single channel, 133 MHz PCI-X-to-Fibre Channel Host Bus Adapter for Windows 2000,
Windows NT and Windows Server 2003 NOTE:
FCA2404 StorageWorks 2 Gb, Fibre Channel Host Bus Adapter is a single channel,
multi-path failover, 133 MHz, PCI-X to Fibre Channel Host Bus Adapter (HBA) with
an embedded multi-mode optical interface for ProLiant Server connects
305573-B21
StorageWorks
2 Gb, Dual Port, 64-Bit/133 MHz PCI-X-to-Fibre Channel Host Bus Adapter for W2K,
Windows Server 2003 and Linux NOTE:
FCA2214DC StorageWorks 2 Gb Dual Port, Fibre Channel Host Bus Adapter is a 64-bit/133
MHz, PCI-X-to Fibre Channel Host Bus Adapter (HBA) with an embedded multi-mode
optical interface.
Modular PDUs 1U/0U (Up to 32 outlets) NOTE: 1U/0U mounting brackets
shipped with
the unit (optimized for 10000 and 9000 series racks).
Fixed Cord Extension Bars NOTE: Two extension bar sticks; each
with (7) C13 plugs.
351655-B21
Fixed Cord PDU NOTE: Four Fixed Cord Extension Bars,
and one 24A, HV mPDU L6-30P core.
351655-D72
HP Modular Power Distribution
Units (mPDU), Low Volt Model, 24A (100-127 VAC) NOTE: This mPDU ( 252663-D71) may
also be used to connect the low volt model of the UPS R3000 XR.
HP Modular Power Distribution
Unit (mPDU), High Volt Model, 40A, Attached Cord
252663-D73
NOTE: This PDU
has a detachable input power cord and allows for adaptability to country
specific power requirements. This model may also be used with the high volt
UPSs R3000 XR and R6000, need to order cable PN 340653-001.
460W HP redundant power supply
with NEMA cord only NOTE: The HP ProLiant DL360 G4 ships
with a single IEC-IEC power cord used for rack mounting with Power Distribution
Units (PDUs). For stand-alone deployments or installation without a rack,
power cord options are available. Model ships with two power cords: IEC-IEC
and NEMA cords.
NOTE: -B21 (pallet) used to ship
empty racks shipped on a truck -B22 (shock pallet) used to ship racks with
equipment installed (by custom systems, VARs and Channels) -B23 (crated) used
for air shipments of empty racks
NOTE: It is mandatory to use a shock
pallet in order to ship racks with equipment installed. Not all HP equipment is
qualified to be shipped in the Rack 10000 series
NOTE: Cat5e cables
are required to connect Interface Adapters to Console Switches. Cat5e cables
can be found at the following URL: http://www.hp.com/go/kvm.
HP 1x 4 USB/PS2 KVM Switch, TT
371301-D71
HP 1x 4 USB/PS2 KVM Switch, RM
371302-B21
HP PS2 KVM Cable with audio, 6',
2-pack
371730-B21
HP USB KVM Cable with audio, 6',
2-pack
371729-B21
NOTE: For additional
information regarding KVM switches, Serial Console servers, rack mount monitors,
keyboards and all related options please see the following URL: http://www.hp.com/go/kvm.
NOTE: Cat5e cables
are required to connect Serial Adapters to Serial Console Servers. Additional
Serial Adapters and Cat5e cables can be found at the following URL: http://www.hp.com/go/kvm.
NOTE: For additional
information regarding KVM switches, Serial Console servers, rack mount monitors,
keyboards and all related options please see the following URL: http://www.hp.com/go/kvm.
Service
and Support Offerings (HP Care Pack Services)
Hardware Services
4-Hour On-site Service
4-Hour On-site Service,
5-Day x 13-Hour Coverage, 3 Years, Electronic
U4496E
4-Hour On-site Service,
7-Day x 24-Hour Coverage, 3 Years, Electronic
U4497E
Hardware Services
6-Hour Call to Repair On-site Service
6-Hour Call to Repair, On-site
Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
U4498E
Hardware Services
Next Business Day On-Site Service
Hardware Installation, Electronic
U4506E
Installation & Start-Up
of a ProLiant server and Microsoft or Linux O/S per the Customer Description
and/or Data Sheet. To be delivered on a scheduled basis 8am-5pm, M-F,
excl. HP holidays, Electronic
U4507E
Support Plus
Onsite HW support, 8am-9pm,
M-F, 4hr response and Microsoft O/S SW Tech support offsite, onsite
at HP's discretion, 8am-9pm, M-F 2hr response time excl. HP holidays,
Electronic
U4508E
Support Plus 24
Onsite HW support 24x7,
4hr response and Microsoft O/S SW Tech support offsite, onsite at
HP's discretion, 24x7 2hr response time incl. HP holidays, Electronic
U4509E
Onsite HW support 24x7,
4hr response and SuSE Linux SW Tech support offsite, onsite at HP's
discretion, 24x7 2hr response time incl. HP holidays, Electronic
U6310E
Onsite HW support 24x7,
4hr response and Red Hat ES2.1 Linux SW Tech support offsite, onsite
at HP's discretion, 24x7 2hr response time incl. HP holidays, Electronic
NOTE:
Memory configurations listed do not apply to "Factory Integrated Models".
HP ProLiant DL360 G4 3.06 GHz and 3.4 GHz-1MB Models
Standard Memory
1 GB PC2700 DDR 333 Registered SDRAM DIMM installed (1 x 1 GB SDRAM DIMM)
Upgrading Memory and Memory Interleaving
When upgrading memory, DIMMs 1A and 2A must match. DIMMs 3B and 4B must
match and must be installed as a pair. When DIMMs 1A and 2A are populated
the system is automatically configured for 2:1 interleaving. When all
four DIMMs are populated with identical DIMMs the system is automatically
configured for bank interleaving. Bank B can be configured for Online
Spare Memory.
Standard Memory Plus Optional Memory
Up to 6 GB memory is available with the standard memory of 1 GB and the
optional installation of PC2700 DDR 333 Registered SDRAM DIMM memory kits.
Standard Memory Replaced with Optional Memory
Up to 8 GB of memory is available with the removal of the standard 1 GB
of memory and the optional installation of PC2700 DDR 333 Registered SDRAM
DIMM memory kits.
NOTE:
Chart does not represent all
possible configurations.
DL360 G4 Memory
Slot
1
2
3
4
Standard
1 GB
1 GB
Empty
Empty
Empty
Optional
6 GB
1 GB
1 GB
2 GB
2 GB
Maximum
8 GB
2 GB
2 GB
2 GB
2 GB
Following are memory options available from HP:
512 MB of Advanced ECC PC2700 DDR 333 SDRAM DIMM Memory Kit (1 x 512
MB)
Standard Memory
2 GB PC2700 DDR 333 Registered SDRAM DIMM installed (2 x 1 GB SDRAM DIMM)
Upgrading Memory and Memory Interleaving
When upgrading memory, DIMMs 1A and 2A must match. DIMMs 3B and 4B must
match and must be installed as a pair. When DIMMs 1A and 2A are populated
the system is automatically configured for 2:1 interleaving. When all
four DIMMs are populated with identical DIMMs the system is automatically
configured for bank interleaving. Bank B can be configured for Online
Spare Memory.
Standard Memory Plus Optional Memory
Up to 6 GB memory is available with the standard memory of 1 GB and the
optional installation of PC2700 DDR 333 Registered SDRAM DIMM memory kits.
Standard Memory Replaced with Optional Memory
Up to 8 GB of memory is available with the removal of the standard 1 GB
of memory and the optional installation of PC2700 DDR 333 Registered SDRAM
DIMM memory kits. NOTE: Chart does not represent
all possible configurations.
DL360 G4 Memory
Slot
1
2
3
4
Standard
2 GB
1 GB
1 GB
Empty
Empty
Optional
6 GB
1 GB
1 GB
2 GB
2 GB
Maximum
8 GB
2 GB
2 GB
2 GB
2 GB
Following are memory options available from HP:
512 MB of Advanced ECC PC2700 DDR 333 SDRAM DIMM Memory Kit (1 x 512
MB)